Bases and stems made from colourless transparent acrylic. Stems according to choice "short" (15 and 20 mm) and/or "long" (30 and 35 mm). The stems may include production related air bubbles and don't represent a defect in the product.

32 mm Base mit 3 mm Loch für Flugstab aus Acryl, Messing, etc. und Markierungen für verschiedene Sektoren und/oder Feuerwinkel. Die Base eignet sich damit perfekt für Spiele wie z.B. Battlefleet Colossus, Full Thrust, Dropfleet Commander oder sonstige Science Fiction Raumschiff Tabletop-Spiele. The pictures show a digital render. The 3D files are from Keiler. These 3D files are produced and sold under a commercial licence. Most of the miniatures are printed after you order them. The long processing time allows me to sensibly plan my working and printing time. Whenever possible, I try to cut the processing time short. The models are delivered unpainted and unassambled. This is a 3D printed product made of UV hardened resin. Models are cleaned and completely cured with UV light. Before printing, a support structure needs to be added to the models, these are normally removed after printing, but leave "scars" on the model. These are production-related and do not represent a defect in the product. Remains of the support structure might still be on the model and can be removed with a sharp hobby knife. Resin dust is a health hazard if inhaled into the lungs. Sanding and filing is not recommended. Otherwise, such work should only be carried out with appropriate protective equipment (fine dust mask) and/or wet sandpaper. It's possible that the models are hollow. In this case, the model has drainage holes through which the liquid resin could leak out. The inside of the model was then also cured. Drainage holes can be closed with modelling putty. Resin is heat-sensitive and can therefore deform during the printing process, the removal of the support structures, post-process curing, or shipping. Hot water or a heat gun/hair dryer can quickly remedy this. The affected part is heated and then carefully bent into the correct position. Important noticeWarning! Not for children under the age of 3. Choking hazard due to small parts.This product is not a toy.

Replica of the planet „Mars“ with 9 cm diameter. Consists of two pieces and includes a small stand. The planet has weak points at the top and bottom, which can be drilled through to put the planet on a metal stem or something similar. The pictures show a digital render. The 3D files are from Titan Shipyards. These 3D files are produced and sold under a commercial licence. Most of the miniatures are printed after you order them. The long processing time allows me to sensibly plan my working and printing time. Whenever possible, I try to cut the processing time short. The models are delivered unpainted and unassambled. This is a 3D printed product made of UV hardened resin. Models are cleaned and completely cured with UV light. Before printing, a support structure needs to be added to the models, these are normally removed after printing, but leave "scars" on the model. These are production-related and do not represent a defect in the product. Remains of the support structure might still be on the model and can be removed with a sharp hobby knife. Resin dust is a health hazard if inhaled into the lungs. Sanding and filing is not recommended. Otherwise, such work should only be carried out with appropriate protective equipment (fine dust mask) and/or wet sandpaper. It's possible that the models are hollow. In this case, the model has drainage holes through which the liquid resin could leak out. The inside of the model was then also cured. Drainage holes can be closed with modelling putty. Resin is heat-sensitive and can therefore deform during the printing process, the removal of the support structures, post-process curing, or shipping. Hot water or a heat gun/hair dryer can quickly remedy this. The affected part is heated and then carefully bent into the correct position. Important noticeWarning! Not for children under the age of 3. Choking hazard due to small parts.This product is not a toy.

Replica of the planet „Mars“ in the far future, full of advanced mechanical facilities and improvements. 9 cm diameter. Consists of two pieces and includes a small stand. The planet has weak points at the top and bottom, which can be drilled through to put the planet on a metal stem or something similar. The pictures show a digital render. The 3D files are from Titan Shipyards. These 3D files are produced and sold under a commercial licence. Most of the miniatures are printed after you order them. The long processing time allows me to sensibly plan my working and printing time. Whenever possible, I try to cut the processing time short. The models are delivered unpainted and unassambled. This is a 3D printed product made of UV hardened resin. Models are cleaned and completely cured with UV light. Before printing, a support structure needs to be added to the models, these are normally removed after printing, but leave "scars" on the model. These are production-related and do not represent a defect in the product. Remains of the support structure might still be on the model and can be removed with a sharp hobby knife. Resin dust is a health hazard if inhaled into the lungs. Sanding and filing is not recommended. Otherwise, such work should only be carried out with appropriate protective equipment (fine dust mask) and/or wet sandpaper. It's possible that the models are hollow. In this case, the model has drainage holes through which the liquid resin could leak out. The inside of the model was then also cured. Drainage holes can be closed with modelling putty. Resin is heat-sensitive and can therefore deform during the printing process, the removal of the support structures, post-process curing, or shipping. Hot water or a heat gun/hair dryer can quickly remedy this. The affected part is heated and then carefully bent into the correct position. Important noticeWarning! Not for children under the age of 3. Choking hazard due to small parts.This product is not a toy.

Base and stems made from colourless transparent acrylic. Stems according to choice "short" (15 and 20 mm) or "long" (30 and 35 mm). The stems may include production related air bubbles and don't represent a defect in the product.

60 mm Base mit 3 mm Loch für Flugstab aus Acryl, Messing, etc. und Markierungen für verschiedene Sektoren und/oder Feuerwinkel. Die Base eignet sich damit perfekt für Spiele wie z.B. Battlefleet Colossus, Full Thrust, Dropfleet Commander oder sonstige Science Fiction Raumschiff Tabletop-Spiele. The pictures show a digital render. The 3D files are from Keiler. These 3D files are produced and sold under a commercial licence. Most of the miniatures are printed after you order them. The long processing time allows me to sensibly plan my working and printing time. Whenever possible, I try to cut the processing time short. The models are delivered unpainted and unassambled. This is a 3D printed product made of UV hardened resin. Models are cleaned and completely cured with UV light. Before printing, a support structure needs to be added to the models, these are normally removed after printing, but leave "scars" on the model. These are production-related and do not represent a defect in the product. Remains of the support structure might still be on the model and can be removed with a sharp hobby knife. Resin dust is a health hazard if inhaled into the lungs. Sanding and filing is not recommended. Otherwise, such work should only be carried out with appropriate protective equipment (fine dust mask) and/or wet sandpaper. It's possible that the models are hollow. In this case, the model has drainage holes through which the liquid resin could leak out. The inside of the model was then also cured. Drainage holes can be closed with modelling putty. Resin is heat-sensitive and can therefore deform during the printing process, the removal of the support structures, post-process curing, or shipping. Hot water or a heat gun/hair dryer can quickly remedy this. The affected part is heated and then carefully bent into the correct position. Important noticeWarning! Not for children under the age of 3. Choking hazard due to small parts.This product is not a toy.

90 mm Base mit 6,35 mm (1/4 Zoll) Loch für Flugstab aus Acryl, Messing, etc. und Markierungen für verschiedene Sektoren und/oder Feuerwinkel. Die Base eignet sich damit perfekt für Spiele wie z.B. Battlefleet Colossus, Full Thrust, Dropfleet Commander oder sonstige Science Fiction Raumschiff Tabletop-Spiele. The pictures show a digital render. The 3D files are from Keiler. These 3D files are produced and sold under a commercial licence. Most of the miniatures are printed after you order them. The long processing time allows me to sensibly plan my working and printing time. Whenever possible, I try to cut the processing time short. The models are delivered unpainted and unassambled. This is a 3D printed product made of UV hardened resin. Models are cleaned and completely cured with UV light. Before printing, a support structure needs to be added to the models, these are normally removed after printing, but leave "scars" on the model. These are production-related and do not represent a defect in the product. Remains of the support structure might still be on the model and can be removed with a sharp hobby knife. Resin dust is a health hazard if inhaled into the lungs. Sanding and filing is not recommended. Otherwise, such work should only be carried out with appropriate protective equipment (fine dust mask) and/or wet sandpaper. It's possible that the models are hollow. In this case, the model has drainage holes through which the liquid resin could leak out. The inside of the model was then also cured. Drainage holes can be closed with modelling putty. Resin is heat-sensitive and can therefore deform during the printing process, the removal of the support structures, post-process curing, or shipping. Hot water or a heat gun/hair dryer can quickly remedy this. The affected part is heated and then carefully bent into the correct position. Important noticeWarning! Not for children under the age of 3. Choking hazard due to small parts.This product is not a toy.

24 corners to mark 6 rectangualar terrain areas with varible size, e.g. for asteroid fields, nebulas, etc. Colour as chosen. The pictured asteroids and game mat are not included. The pictures show a printed product, often in conjunction with additional digital render images. The prints are usually without final cleanup, shown as delivered. The final colour of the material may differ. Most of the miniatures are printed after you order them. The long processing time allows me to sensibly plan my working and printing time. Whenever possible, I try to cut the processing time short. The models are delivered unpainted and unassambled. This is a 3D printed product made of PLA filament (FDM print). Before printing, a support structure may need to be added to the product. These are usually removed after printing, but leave "scars". The product may also have small bumps and grooves. With FDM printing, layer line are also visible. All of this is production-related and does not represent a defect in the product PLA dust is a health hazard if inhaled into the lungs. Sanding and filing should only be carried out with appropriate protective equipment (fine dust mask) and/or wet sandpaper. The product is filled with a filling pattern on the inside, it is not a completely solid product. The product must not be used in direct sunlight or near heat sources. PLA is sensitive to heat and can deform when exposed to heat and sunlight. Deformation is permanent and a user error.PLA waste must be disposed of in household waste; despite often stated otherwise, it is not readily biodegradable. Important noticeWarning! Not for children under the age of 3. Choking hazard due to small parts.This product is not a toy.

Attack wave markers for collectors, painters and gamers, eg. for Battlefleet Colossus, Firestorm Armada, Full Thrust, A Billion Suns, Warfleets: FTL, Dropfleet Commander or other Science Fiction spaceship miniature wargames. 5x fighter markers (5 ships), 5x bomber markers (3 ships). Stackable. Please note that the models are supplied WITHOUT bases. The 3D files are from NofixedForge. These 3D files are produced and sold under a commercial licence. Printed and painted model by NofixedForge. Most of the miniatures are printed after you order them. The long processing time allows me to sensibly plan my working and printing time. Whenever possible, I try to cut the processing time short. The models are delivered unpainted and unassambled. This is a 3D printed product made of UV hardened resin. Models are cleaned and completely cured with UV light. Before printing, a support structure needs to be added to the models, these are normally removed after printing, but leave "scars" on the model. These are production-related and do not represent a defect in the product. Remains of the support structure might still be on the model and can be removed with a sharp hobby knife. Resin dust is a health hazard if inhaled into the lungs. Sanding and filing is not recommended. Otherwise, such work should only be carried out with appropriate protective equipment (fine dust mask) and/or wet sandpaper. It's possible that the models are hollow. In this case, the model has drainage holes through which the liquid resin could leak out. The inside of the model was then also cured. Drainage holes can be closed with modelling putty. Resin is heat-sensitive and can therefore deform during the printing process, the removal of the support structures, post-process curing, or shipping. Hot water or a heat gun/hair dryer can quickly remedy this. The affected part is heated and then carefully bent into the correct position. Important noticeWarning! Not for children under the age of 3. Choking hazard due to small parts.This product is not a toy.

Attack wave markers for collectors, painters and gamers, eg. for Battlefleet Colossus, Firestorm Armada, Full Thrust, A Billion Suns, Warfleets: FTL, Dropfleet Commander or other Science Fiction spaceship miniature wargames. 5x fighter markers (5 ships), 5x bomber markers (3 ships), 5x assault boat markers (2 ships). Stackable. Please note that the models are supplied WITHOUT bases. The pictures show a digital render. The 3D files are from Keiler. These 3D files are produced and sold under a commercial licence. Most of the miniatures are printed after you order them. The long processing time allows me to sensibly plan my working and printing time. Whenever possible, I try to cut the processing time short. The models are delivered unpainted and unassambled. This is a 3D printed product made of UV hardened resin. Models are cleaned and completely cured with UV light. Before printing, a support structure needs to be added to the models, these are normally removed after printing, but leave "scars" on the model. These are production-related and do not represent a defect in the product. Remains of the support structure might still be on the model and can be removed with a sharp hobby knife. Resin dust is a health hazard if inhaled into the lungs. Sanding and filing is not recommended. Otherwise, such work should only be carried out with appropriate protective equipment (fine dust mask) and/or wet sandpaper. It's possible that the models are hollow. In this case, the model has drainage holes through which the liquid resin could leak out. The inside of the model was then also cured. Drainage holes can be closed with modelling putty. Resin is heat-sensitive and can therefore deform during the printing process, the removal of the support structures, post-process curing, or shipping. Hot water or a heat gun/hair dryer can quickly remedy this. The affected part is heated and then carefully bent into the correct position. Important noticeWarning! Not for children under the age of 3. Choking hazard due to small parts.This product is not a toy.

Attack Craft markers of the Swarm. For collectors, painters and gamers, eg. for Battlefleet Colossus, Firestorm Armada, Full Thrust, A Billion Suns, Warfleets: FTL, Dropfleet Commander or other Science Fiction spaceship miniature wargames. The pictures show a digital render. The 3D files are from Arcane Shipyard. These 3D files are produced and sold under a commercial licence. Most of the miniatures are printed after you order them. The long processing time allows me to sensibly plan my working and printing time. Whenever possible, I try to cut the processing time short. The models are delivered unpainted and unassambled. This is a 3D printed product made of UV hardened resin. Models are cleaned and completely cured with UV light. Before printing, a support structure needs to be added to the models, these are normally removed after printing, but leave "scars" on the model. These are production-related and do not represent a defect in the product. Remains of the support structure might still be on the model and can be removed with a sharp hobby knife. Resin dust is a health hazard if inhaled into the lungs. Sanding and filing is not recommended. Otherwise, such work should only be carried out with appropriate protective equipment (fine dust mask) and/or wet sandpaper. It's possible that the models are hollow. In this case, the model has drainage holes through which the liquid resin could leak out. The inside of the model was then also cured. Drainage holes can be closed with modelling putty. Resin is heat-sensitive and can therefore deform during the printing process, the removal of the support structures, post-process curing, or shipping. Hot water or a heat gun/hair dryer can quickly remedy this. The affected part is heated and then carefully bent into the correct position. Important noticeWarning! Not for children under the age of 3. Choking hazard due to small parts.This product is not a toy.

For space miniature war- and boardgames like e.g. for Battlefleet Colossus, Dropfleet Commander, Firestorm Armada, Full Thrust, A Billion Suns, Warfleets: FTL, Void Admiral, Brutal Space, or Twilight Imperium. 6 markers per set, each showing one of the 6 orders. Colours Green/Black as pictures, if requested other colours are available too.Measurements: 20 x 20 x 3 mm The pictures show a printed product, often in conjunction with additional digital render images. The prints are usually without final cleanup, shown as delivered. The final colour of the material may differ. The 3D files are from Italianmoose. These 3D files are produced and sold under a commercial licence. Most of the miniatures are printed after you order them. The long processing time allows me to sensibly plan my working and printing time. Whenever possible, I try to cut the processing time short. The models are delivered unpainted and unassambled. This is a 3D printed product made of PLA filament (FDM print). Before printing, a support structure may need to be added to the product. These are usually removed after printing, but leave "scars". The product may also have small bumps and grooves. With FDM printing, layer line are also visible. All of this is production-related and does not represent a defect in the product PLA dust is a health hazard if inhaled into the lungs. Sanding and filing should only be carried out with appropriate protective equipment (fine dust mask) and/or wet sandpaper. The product is filled with a filling pattern on the inside, it is not a completely solid product. The product must not be used in direct sunlight or near heat sources. PLA is sensitive to heat and can deform when exposed to heat and sunlight. Deformation is permanent and a user error.PLA waste must be disposed of in household waste; despite often stated otherwise, it is not readily biodegradable. Important noticeWarning! Not for children under the age of 3. Choking hazard due to small parts.This product is not a toy.

Don't feel like painting bases because you'd rather invest the time in the models? Want to just start playing straight away? Battleready Flight Bases are simple, functional, and ready to use. Insert the acrylic rod, mount the ship, let's go! 32 mm bases with beveled edges. Manufactured with multi-colour printing and 100% infill for increased weight. The surface has been printed with a smoothing layer. With a layer height of 0.08 mm, the typical stair effect of FDM prints is only barely visible on the sides. Colours: Black (Base), White or chosen Colour 1 (Flying direction), Red or chosen Colour 2 (Fire arcs) Attention! A colour selection varying from the default is a special order and is not subject to the normal right of withdrawal. Content: 20 bases and 20 acrylic flying stems as chosen Stems according to choice "short" (15 and 20 mm) and/or "long" (30 and 35 mm). The stems may include production related air bubbles and don't represent a defect in the product. Shown model is for illustrative purposes only and is not included. The pictures show a printed product, often in conjunction with additional digital render images. The prints are usually without final cleanup, shown as delivered. The final colour of the material may differ. Most of the miniatures are printed after you order them. The long processing time allows me to sensibly plan my working and printing time. Whenever possible, I try to cut the processing time short. The models are delivered unpainted and unassambled. This is a 3D printed product made of PLA filament (FDM print). Before printing, a support structure may need to be added to the product. These are usually removed after printing, but leave "scars". The product may also have small bumps and grooves. With FDM printing, layer line are also visible. All of this is production-related and does not represent a defect in the product PLA dust is a health hazard if inhaled into the lungs. Sanding and filing should only be carried out with appropriate protective equipment (fine dust mask) and/or wet sandpaper. The product is filled with a filling pattern on the inside, it is not a completely solid product. The product must not be used in direct sunlight or near heat sources. PLA is sensitive to heat and can deform when exposed to heat and sunlight. Deformation is permanent and a user error.PLA waste must be disposed of in household waste; despite often stated otherwise, it is not readily biodegradable. Important noticeWarning! Not for children under the age of 3. Choking hazard due to small parts.This product is not a toy.

Don't feel like painting bases because you'd rather invest the time in the models? Want to just start playing straight away? Battleready Flight Bases are simple, functional, and ready to use. Insert the acrylic rod, mount the ship, let's go! 32 mm bases with beveled edges. Manufactured with multi-colour printing and 100% infill for increased weight. The surface has been printed with a smoothing layer. With a layer height of 0.08 mm, the typical stair effect of FDM prints is only barely visible on the sides. Colours: Black (Base), White (Flying direction), Red (Fire arcs) Content: 3 bases and 4 acrylic flying stems as chosen Stems according to choice "short" (15 and 20 mm) and/or "long" (30 and 35 mm). The stems may include production related air bubbles and don't represent a defect in the product. Shown model is for illustrative purposes only and is not included. The pictures show a printed product, often in conjunction with additional digital render images. The prints are usually without final cleanup, shown as delivered. The final colour of the material may differ. Most of the miniatures are printed after you order them. The long processing time allows me to sensibly plan my working and printing time. Whenever possible, I try to cut the processing time short. The models are delivered unpainted and unassambled. This is a 3D printed product made of PLA filament (FDM print). Before printing, a support structure may need to be added to the product. These are usually removed after printing, but leave "scars". The product may also have small bumps and grooves. With FDM printing, layer line are also visible. All of this is production-related and does not represent a defect in the product PLA dust is a health hazard if inhaled into the lungs. Sanding and filing should only be carried out with appropriate protective equipment (fine dust mask) and/or wet sandpaper. The product is filled with a filling pattern on the inside, it is not a completely solid product. The product must not be used in direct sunlight or near heat sources. PLA is sensitive to heat and can deform when exposed to heat and sunlight. Deformation is permanent and a user error.PLA waste must be disposed of in household waste; despite often stated otherwise, it is not readily biodegradable. Important noticeWarning! Not for children under the age of 3. Choking hazard due to small parts.This product is not a toy.

Don't feel like painting bases because you'd rather invest the time in the models? Want to just start playing straight away? Battleready Flight Bases are simple, functional, and ready to use. Insert the acrylic rod, mount the ship, let's go! 60 mm bases with beveled edges. Manufactured with multi-colour printing and 100% infill for increased weight. The surface has been printed with a smoothing layer. With a layer height of 0.08 mm, the typical stair effect of FDM prints is only barely visible on the sides. Colours: Black (Base), White (Flying direction), Red (Fire arcs) Content: 2 bases and 2 acrylic flying stems as chosen Stems according to choice "short" (15 and 20 mm) or "long" (30 and 35 mm). The stems may include production related air bubbles and don't represent a defect in the product. Shown model is for illustrative purposes only and is not included. The pictures show a printed product, often in conjunction with additional digital render images. The prints are usually without final cleanup, shown as delivered. The final colour of the material may differ. Most of the miniatures are printed after you order them. The long processing time allows me to sensibly plan my working and printing time. Whenever possible, I try to cut the processing time short. The models are delivered unpainted and unassambled. This is a 3D printed product made of PLA filament (FDM print). Before printing, a support structure may need to be added to the product. These are usually removed after printing, but leave "scars". The product may also have small bumps and grooves. With FDM printing, layer line are also visible. All of this is production-related and does not represent a defect in the product PLA dust is a health hazard if inhaled into the lungs. Sanding and filing should only be carried out with appropriate protective equipment (fine dust mask) and/or wet sandpaper. The product is filled with a filling pattern on the inside, it is not a completely solid product. The product must not be used in direct sunlight or near heat sources. PLA is sensitive to heat and can deform when exposed to heat and sunlight. Deformation is permanent and a user error.PLA waste must be disposed of in household waste; despite often stated otherwise, it is not readily biodegradable. Important noticeWarning! Not for children under the age of 3. Choking hazard due to small parts.This product is not a toy.

Don't feel like painting bases because you'd rather invest the time in the models? Want to just start playing straight away? Battleready Flight Bases are simple, functional, and ready to use. Insert the acrylic rod, mount the ship, let's go! 60 mm bases with beveled edges. Manufactured with multi-colour printing and 100% infill for increased weight. The surface has been printed with a smoothing layer. With a layer height of 0.08 mm, the typical stair effect of FDM prints is only barely visible on the sides. Colours: Black (Base), White or chosen Colour 1 (Flying direction), Red or chosen Colour 2 (Fire arcs) Attention! A colour selection varying from the default is a special order and is not subject to the normal right of withdrawal. Content: 6 bases and 6 acrylic flying stems as chosen Stems according to choice "short" (15 and 20 mm) and/or "long" (30 and 35 mm). The stems may include production related air bubbles and don't represent a defect in the product. Shown model is for illustrative purposes only and is not included. The pictures show a printed product, often in conjunction with additional digital render images. The prints are usually without final cleanup, shown as delivered. The final colour of the material may differ. Most of the miniatures are printed after you order them. The long processing time allows me to sensibly plan my working and printing time. Whenever possible, I try to cut the processing time short. The models are delivered unpainted and unassambled. This is a 3D printed product made of PLA filament (FDM print). Before printing, a support structure may need to be added to the product. These are usually removed after printing, but leave "scars". The product may also have small bumps and grooves. With FDM printing, layer line are also visible. All of this is production-related and does not represent a defect in the product PLA dust is a health hazard if inhaled into the lungs. Sanding and filing should only be carried out with appropriate protective equipment (fine dust mask) and/or wet sandpaper. The product is filled with a filling pattern on the inside, it is not a completely solid product. The product must not be used in direct sunlight or near heat sources. PLA is sensitive to heat and can deform when exposed to heat and sunlight. Deformation is permanent and a user error.PLA waste must be disposed of in household waste; despite often stated otherwise, it is not readily biodegradable. Important noticeWarning! Not for children under the age of 3. Choking hazard due to small parts.This product is not a toy.

Game markers for collectors, painters and gamers, eg. for Battlefleet Colossus, Firestorm Armada, Full Thrust, A Billion Suns, Warfleets: FTL, Dropfleet Commander or other Science Fiction spaceship miniature wargames. The markers measure approx. 28,15 x 23,67 mm at their widest points. Please note: the blast markers will be delivered on a sprue (see pictures) and should be removed with sharp hobby clippers. The 3D files are from NofixedForge. These 3D files are produced and sold under a commercial licence. Most of the miniatures are printed after you order them. The long processing time allows me to sensibly plan my working and printing time. Whenever possible, I try to cut the processing time short. The models are delivered unpainted and unassambled. This is a 3D printed product made of UV hardened resin. Models are cleaned and completely cured with UV light. Before printing, a support structure needs to be added to the models, these are normally removed after printing, but leave "scars" on the model. These are production-related and do not represent a defect in the product. Remains of the support structure might still be on the model and can be removed with a sharp hobby knife. Resin dust is a health hazard if inhaled into the lungs. Sanding and filing is not recommended. Otherwise, such work should only be carried out with appropriate protective equipment (fine dust mask) and/or wet sandpaper. It's possible that the models are hollow. In this case, the model has drainage holes through which the liquid resin could leak out. The inside of the model was then also cured. Drainage holes can be closed with modelling putty. Resin is heat-sensitive and can therefore deform during the printing process, the removal of the support structures, post-process curing, or shipping. Hot water or a heat gun/hair dryer can quickly remedy this. The affected part is heated and then carefully bent into the correct position. Important noticeWarning! Not for children under the age of 3. Choking hazard due to small parts.This product is not a toy.

Flyer base with 2 mm hole for an acrylic, brass, etc. rodand markings for different sections or fire arcs. This makes base perfectly fitted for games like Battlefleet Colossus, Firestorm Armada, Full Thrust, A Billion Suns, Warfleets: FTL, Dropfleet Commander or other Science Fiction spaceship miniature wargames. Please note that the models are supplied WITHOUT bases. The 3D files are from NofixedForge. These 3D files are produced and sold under a commercial licence. Printed and painted model by NofixedForge. Most of the miniatures are printed after you order them. The long processing time allows me to sensibly plan my working and printing time. Whenever possible, I try to cut the processing time short. The models are delivered unpainted and unassambled. This is a 3D printed product made of UV hardened resin. Models are cleaned and completely cured with UV light. Before printing, a support structure needs to be added to the models, these are normally removed after printing, but leave "scars" on the model. These are production-related and do not represent a defect in the product. Remains of the support structure might still be on the model and can be removed with a sharp hobby knife. Resin dust is a health hazard if inhaled into the lungs. Sanding and filing is not recommended. Otherwise, such work should only be carried out with appropriate protective equipment (fine dust mask) and/or wet sandpaper. It's possible that the models are hollow. In this case, the model has drainage holes through which the liquid resin could leak out. The inside of the model was then also cured. Drainage holes can be closed with modelling putty. Resin is heat-sensitive and can therefore deform during the printing process, the removal of the support structures, post-process curing, or shipping. Hot water or a heat gun/hair dryer can quickly remedy this. The affected part is heated and then carefully bent into the correct position. Important noticeWarning! Not for children under the age of 3. Choking hazard due to small parts.This product is not a toy.

10x flying stems with 4 mm ball head. Suitable for spaceship models from Edge Miniatures.The pictures show a digital render. The 3D files are from Edge Miniatures. These 3D files are produced and sold under a commercial licence. Most of the miniatures are printed after you order them. The long processing time allows me to sensibly plan my working and printing time. Whenever possible, I try to cut the processing time short. The models are delivered unpainted and unassambled. This is a 3D printed product made of UV hardened resin. Models are cleaned and completely cured with UV light. Before printing, a support structure needs to be added to the models, these are normally removed after printing, but leave "scars" on the model. These are production-related and do not represent a defect in the product. Remains of the support structure might still be on the model and can be removed with a sharp hobby knife. Resin dust is a health hazard if inhaled into the lungs. Sanding and filing is not recommended. Otherwise, such work should only be carried out with appropriate protective equipment (fine dust mask) and/or wet sandpaper. It's possible that the models are hollow. In this case, the model has drainage holes through which the liquid resin could leak out. The inside of the model was then also cured. Drainage holes can be closed with modelling putty. Resin is heat-sensitive and can therefore deform during the printing process, the removal of the support structures, post-process curing, or shipping. Hot water or a heat gun/hair dryer can quickly remedy this. The affected part is heated and then carefully bent into the correct position. Important noticeWarning! Not for children under the age of 3. Choking hazard due to small parts.This product is not a toy.

Mechanical planet ring, fitting for 3D planets with 9 cm diameter, like the "Mars" or "Tech-Mars". Consisting of four parts. Additionally includes 16 spires with 4 or 6 mm height respectively, which can be freely attached to the ring. The pictures show a digital render. Pictures may show additional models for size comparison. These addtional models are not part of this product. The 3D files are from Titan Shipyards. These 3D files are produced and sold under a commercial licence. Most of the miniatures are printed after you order them. The long processing time allows me to sensibly plan my working and printing time. Whenever possible, I try to cut the processing time short. The models are delivered unpainted and unassambled. This is a 3D printed product made of UV hardened resin. Models are cleaned and completely cured with UV light. Before printing, a support structure needs to be added to the models, these are normally removed after printing, but leave "scars" on the model. These are production-related and do not represent a defect in the product. Remains of the support structure might still be on the model and can be removed with a sharp hobby knife. Resin dust is a health hazard if inhaled into the lungs. Sanding and filing is not recommended. Otherwise, such work should only be carried out with appropriate protective equipment (fine dust mask) and/or wet sandpaper. It's possible that the models are hollow. In this case, the model has drainage holes through which the liquid resin could leak out. The inside of the model was then also cured. Drainage holes can be closed with modelling putty. Resin is heat-sensitive and can therefore deform during the printing process, the removal of the support structures, post-process curing, or shipping. Hot water or a heat gun/hair dryer can quickly remedy this. The affected part is heated and then carefully bent into the correct position. Important noticeWarning! Not for children under the age of 3. Choking hazard due to small parts.This product is not a toy.

Planet template with 10 cm diameter and "Sire" design, e.g. for Battlefleet Colossus, Full Thrust, Dropfleet Commander or other Science Fiction spaceship wargames.The template is made of plastic, with a protective layer on the top and black anti-slip foam at the bottom.Pictured models on the images are only for size comparison and are not part of the listing.

Planet template with 19 cm diameter and "Venus" design, e.g. for Battlefleet Colossus, Full Thrust, Dropfleet Commander or other Science Fiction spaceship wargames.Sadly, the print is a bit blurry, therefore this item is reduced in price.The template is made of plastic, with a protective layer on the top and black anti-slip foam at the bottom.Pictured models on the images are only for size comparison and are not part of the listing.

Planet template with 25 cm diameter and "Neptune" design, e.g. for Battlefleet Colossus, Full Thrust, Dropfleet Commander or other Science Fiction spaceship wargames.The template is made of plastic, with a protective layer on the top and black anti-slip foam at the bottom.Pictured models on the images are only for size comparison and are not part of the listing.

20 mm Assault Boats markers of the Rage Lizards for collectors, painters and gamers, eg. for Battlefleet Colossus, Firestorm Armada, Full Thrust, A Billion Suns, Warfleets: FTL, Dropfleet Commander or other Science Fiction spaceship miniature wargame.Please note that the models are supplied WITHOUT bases. The pictures show a digital render. The 3D files are from Arcane Shipyard. These 3D files are produced and sold under a commercial licence. Most of the miniatures are printed after you order them. The long processing time allows me to sensibly plan my working and printing time. Whenever possible, I try to cut the processing time short. The models are delivered unpainted and unassambled. This is a 3D printed product made of UV hardened resin. Models are cleaned and completely cured with UV light. Before printing, a support structure needs to be added to the models, these are normally removed after printing, but leave "scars" on the model. These are production-related and do not represent a defect in the product. Remains of the support structure might still be on the model and can be removed with a sharp hobby knife. Resin dust is a health hazard if inhaled into the lungs. Sanding and filing is not recommended. Otherwise, such work should only be carried out with appropriate protective equipment (fine dust mask) and/or wet sandpaper. It's possible that the models are hollow. In this case, the model has drainage holes through which the liquid resin could leak out. The inside of the model was then also cured. Drainage holes can be closed with modelling putty. Resin is heat-sensitive and can therefore deform during the printing process, the removal of the support structures, post-process curing, or shipping. Hot water or a heat gun/hair dryer can quickly remedy this. The affected part is heated and then carefully bent into the correct position. Important noticeWarning! Not for children under the age of 3. Choking hazard due to small parts.This product is not a toy.