Swarm Claw Krakens (3 models)

Attack Craft markers of the Swarm. For collectors, painters and gamers, eg. for Battlefleet Gothic, Firestorm Armada, Full Thrust, A Billion Suns, Warfleets: FTL, Dropfleet Commander or other Science Fiction spaceship miniature wargames. The pictures show a digital render. The 3D files are from Arcane Shipyard. These 3D files are produced and sold under a commercial licence. Most of the miniatures are printed after you order them. The long processing time allows me to sensibly plan my working and printing time. Whenever possible, I try to cut the processing time short. The models are delivered unpainted and unassambled. This is a 3D printed product made of UV hardened resin. Models are cleaned and completely cured with UV light. Before printing, a support structure needs to be added to the models, these are normally removed after printing, but leave "scars" on the model. These are production-related and do not represent a defect in the product. Remains of the support structure might still be on the model and can be removed with a sharp hobby knife. Resin dust is a health hazard if inhaled into the lungs. Sanding and filing is not recommended. Otherwise, such work should only be carried out with appropriate protective equipment (fine dust mask) and/or wet sandpaper. It's possible that the models are hollow. In this case, the model has drainage holes through which the liquid resin could leak out. The inside of the model was then also cured. Drainage holes can be closed with modelling putty. Resin is heat-sensitive and can therefore deform during the printing process, the removal of the support structures, post-process curing, or shipping. Hot water or a heat gun/hair dryer can quickly remedy this. The affected part is heated and then carefully bent into the correct position. Important noticeWarning! Not for children under the age of 3. Choking hazard due to small parts.This product is not a toy.

Swarm spaceships for collectors, painters and gamers, eg. for Battlefleet Gothic, Firestorm Armada, Full Thrust, A Billion Suns, Warfleets: FTL, Dropfleet Commander or other Science Fiction spaceship miniature wargames. Please note that the models are supplied WITHOUT bases. The pictures show a digital render. The 3D files are from NofixedForge These 3D files are produced and sold under a commercial licence. Printed and painted model by NofixedForge. Most of the miniatures are printed after you order them. The long processing time allows me to sensibly plan my working and printing time. Whenever possible, I try to cut the processing time short. The models are delivered unpainted and unassambled. This is a 3D printed product made of UV hardened resin. Models are cleaned and completely cured with UV light. Before printing, a support structure needs to be added to the models, these are normally removed after printing, but leave "scars" on the model. These are production-related and do not represent a defect in the product. Remains of the support structure might still be on the model and can be removed with a sharp hobby knife. Resin dust is a health hazard if inhaled into the lungs. Sanding and filing is not recommended. Otherwise, such work should only be carried out with appropriate protective equipment (fine dust mask) and/or wet sandpaper. It's possible that the models are hollow. In this case, the model has drainage holes through which the liquid resin could leak out. The inside of the model was then also cured. Drainage holes can be closed with modelling putty. Resin is heat-sensitive and can therefore deform during the printing process, the removal of the support structures, post-process curing, or shipping. Hot water or a heat gun/hair dryer can quickly remedy this. The affected part is heated and then carefully bent into the correct position. Important noticeWarning! Not for children under the age of 3. Choking hazard due to small parts.This product is not a toy.

Swarm spaceship. For collectors, painters and gamers, eg. for Battlefleet Gothic, Firestorm Armada, Full Thrust, A Billion Suns, Warfleets: FTL, Dropfleet Commander or other Science Fiction spaceship miniature wargames. Please note that the models are supplied WITHOUT bases. The pictures show a digital render. The 3D files are from Baukloetzchen. These 3D files are produced and sold under a commercial licence. Most of the miniatures are printed after you order them. The long processing time allows me to sensibly plan my working and printing time. Whenever possible, I try to cut the processing time short. The models are delivered unpainted and unassambled. This is a 3D printed product made of UV hardened resin. Models are cleaned and completely cured with UV light. Before printing, a support structure needs to be added to the models, these are normally removed after printing, but leave "scars" on the model. These are production-related and do not represent a defect in the product. Remains of the support structure might still be on the model and can be removed with a sharp hobby knife. Resin dust is a health hazard if inhaled into the lungs. Sanding and filing is not recommended. Otherwise, such work should only be carried out with appropriate protective equipment (fine dust mask) and/or wet sandpaper. It's possible that the models are hollow. In this case, the model has drainage holes through which the liquid resin could leak out. The inside of the model was then also cured. Drainage holes can be closed with modelling putty. Resin is heat-sensitive and can therefore deform during the printing process, the removal of the support structures, post-process curing, or shipping. Hot water or a heat gun/hair dryer can quickly remedy this. The affected part is heated and then carefully bent into the correct position. Important noticeWarning! Not for children under the age of 3. Choking hazard due to small parts.This product is not a toy.

Swarm spaceship. For collectors, painters and gamers, eg. for Battlefleet Gothic, Firestorm Armada, Full Thrust, A Billion Suns, Warfleets: FTL, Dropfleet Commander or other Science Fiction spaceship miniature wargames. Please note that the models are supplied WITHOUT bases. The pictures show a digital render. The 3D files are from Baukloetzchen. These 3D files are produced and sold under a commercial licence. Most of the miniatures are printed after you order them. The long processing time allows me to sensibly plan my working and printing time. Whenever possible, I try to cut the processing time short. The models are delivered unpainted and unassambled. This is a 3D printed product made of UV hardened resin. Models are cleaned and completely cured with UV light. Before printing, a support structure needs to be added to the models, these are normally removed after printing, but leave "scars" on the model. These are production-related and do not represent a defect in the product. Remains of the support structure might still be on the model and can be removed with a sharp hobby knife. Resin dust is a health hazard if inhaled into the lungs. Sanding and filing is not recommended. Otherwise, such work should only be carried out with appropriate protective equipment (fine dust mask) and/or wet sandpaper. It's possible that the models are hollow. In this case, the model has drainage holes through which the liquid resin could leak out. The inside of the model was then also cured. Drainage holes can be closed with modelling putty. Resin is heat-sensitive and can therefore deform during the printing process, the removal of the support structures, post-process curing, or shipping. Hot water or a heat gun/hair dryer can quickly remedy this. The affected part is heated and then carefully bent into the correct position. Important noticeWarning! Not for children under the age of 3. Choking hazard due to small parts.This product is not a toy.

For space miniature war- and boardgames like e.g. for Battlefleet Gothic, Dropfleet Commander, Firestorm Armada, Full Thrust, A Billion Suns, Warfleets: FTL, Void Admiral, Brutal Space, or Twilight Imperium. Please note that the models are supplied WITHOUT bases. The pictures show a digital render. The 3D files are from Baukloetzchen. These 3D files are produced and sold under a commercial licence. Most of the miniatures are printed after you order them. The long processing time allows me to sensibly plan my working and printing time. Whenever possible, I try to cut the processing time short. The models are delivered unpainted and unassambled. This is a 3D printed product made of UV hardened resin. Models are cleaned and completely cured with UV light. Before printing, a support structure needs to be added to the models, these are normally removed after printing, but leave "scars" on the model. These are production-related and do not represent a defect in the product. Remains of the support structure might still be on the model and can be removed with a sharp hobby knife. Resin dust is a health hazard if inhaled into the lungs. Sanding and filing is not recommended. Otherwise, such work should only be carried out with appropriate protective equipment (fine dust mask) and/or wet sandpaper. It's possible that the models are hollow. In this case, the model has drainage holes through which the liquid resin could leak out. The inside of the model was then also cured. Drainage holes can be closed with modelling putty. Resin is heat-sensitive and can therefore deform during the printing process, the removal of the support structures, post-process curing, or shipping. Hot water or a heat gun/hair dryer can quickly remedy this. The affected part is heated and then carefully bent into the correct position. Important noticeWarning! Not for children under the age of 3. Choking hazard due to small parts.This product is not a toy.

For space miniature war- and boardgames like e.g. for Battlefleet Gothic, Dropfleet Commander, Firestorm Armada, Full Thrust, A Billion Suns, Warfleets: FTL, Void Admiral, Brutal Space, or Twilight Imperium. Please note that the models are supplied WITHOUT bases. The pictures show a digital render. The 3D files are from Baukloetzchen. These 3D files are produced and sold under a commercial licence. Most of the miniatures are printed after you order them. The long processing time allows me to sensibly plan my working and printing time. Whenever possible, I try to cut the processing time short. The models are delivered unpainted and unassambled. This is a 3D printed product made of UV hardened resin. Models are cleaned and completely cured with UV light. Before printing, a support structure needs to be added to the models, these are normally removed after printing, but leave "scars" on the model. These are production-related and do not represent a defect in the product. Remains of the support structure might still be on the model and can be removed with a sharp hobby knife. Resin dust is a health hazard if inhaled into the lungs. Sanding and filing is not recommended. Otherwise, such work should only be carried out with appropriate protective equipment (fine dust mask) and/or wet sandpaper. It's possible that the models are hollow. In this case, the model has drainage holes through which the liquid resin could leak out. The inside of the model was then also cured. Drainage holes can be closed with modelling putty. Resin is heat-sensitive and can therefore deform during the printing process, the removal of the support structures, post-process curing, or shipping. Hot water or a heat gun/hair dryer can quickly remedy this. The affected part is heated and then carefully bent into the correct position. Important noticeWarning! Not for children under the age of 3. Choking hazard due to small parts.This product is not a toy.

Swarm spaceship. For collectors, painters and gamers, eg. for Battlefleet Gothic, Firestorm Armada, Full Thrust, A Billion Suns, Warfleets: FTL, Dropfleet Commander or other Science Fiction spaceship miniature wargames. Please note that the models are supplied WITHOUT bases. The pictures show a digital render. The 3D files are from Baukloetzchen. These 3D files are produced and sold under a commercial licence. Most of the miniatures are printed after you order them. The long processing time allows me to sensibly plan my working and printing time. Whenever possible, I try to cut the processing time short. The models are delivered unpainted and unassambled. This is a 3D printed product made of UV hardened resin. Models are cleaned and completely cured with UV light. Before printing, a support structure needs to be added to the models, these are normally removed after printing, but leave "scars" on the model. These are production-related and do not represent a defect in the product. Remains of the support structure might still be on the model and can be removed with a sharp hobby knife. Resin dust is a health hazard if inhaled into the lungs. Sanding and filing is not recommended. Otherwise, such work should only be carried out with appropriate protective equipment (fine dust mask) and/or wet sandpaper. It's possible that the models are hollow. In this case, the model has drainage holes through which the liquid resin could leak out. The inside of the model was then also cured. Drainage holes can be closed with modelling putty. Resin is heat-sensitive and can therefore deform during the printing process, the removal of the support structures, post-process curing, or shipping. Hot water or a heat gun/hair dryer can quickly remedy this. The affected part is heated and then carefully bent into the correct position. Important noticeWarning! Not for children under the age of 3. Choking hazard due to small parts.This product is not a toy.

Swarm spaceships for collectors, painters and gamers, eg. for Battlefleet Gothic, Firestorm Armada, Full Thrust, A Billion Suns, Warfleets: FTL, Dropfleet Commander or other Science Fiction spaceship miniature wargames. Please note that the models are supplied WITHOUT bases. The pictures show a digital render. The 3D files are from NofixedForge These 3D files are produced and sold under a commercial licence. Printed and painted model by NofixedForge. Most of the miniatures are printed after you order them. The long processing time allows me to sensibly plan my working and printing time. Whenever possible, I try to cut the processing time short. The models are delivered unpainted and unassambled. This is a 3D printed product made of UV hardened resin. Models are cleaned and completely cured with UV light. Before printing, a support structure needs to be added to the models, these are normally removed after printing, but leave "scars" on the model. These are production-related and do not represent a defect in the product. Remains of the support structure might still be on the model and can be removed with a sharp hobby knife. Resin dust is a health hazard if inhaled into the lungs. Sanding and filing is not recommended. Otherwise, such work should only be carried out with appropriate protective equipment (fine dust mask) and/or wet sandpaper. It's possible that the models are hollow. In this case, the model has drainage holes through which the liquid resin could leak out. The inside of the model was then also cured. Drainage holes can be closed with modelling putty. Resin is heat-sensitive and can therefore deform during the printing process, the removal of the support structures, post-process curing, or shipping. Hot water or a heat gun/hair dryer can quickly remedy this. The affected part is heated and then carefully bent into the correct position. Important noticeWarning! Not for children under the age of 3. Choking hazard due to small parts.This product is not a toy.

Swarm spaceship. For collectors, painters and gamers, eg. for Battlefleet Gothic, Firestorm Armada, Full Thrust, A Billion Suns, Warfleets: FTL, Dropfleet Commander or other Science Fiction spaceship miniature wargames. Please note that the models are supplied WITHOUT bases. The pictures show a digital render. The 3D files are from Baukloetzchen. These 3D files are produced and sold under a commercial licence. Most of the miniatures are printed after you order them. The long processing time allows me to sensibly plan my working and printing time. Whenever possible, I try to cut the processing time short. The models are delivered unpainted and unassambled. This is a 3D printed product made of UV hardened resin. Models are cleaned and completely cured with UV light. Before printing, a support structure needs to be added to the models, these are normally removed after printing, but leave "scars" on the model. These are production-related and do not represent a defect in the product. Remains of the support structure might still be on the model and can be removed with a sharp hobby knife. Resin dust is a health hazard if inhaled into the lungs. Sanding and filing is not recommended. Otherwise, such work should only be carried out with appropriate protective equipment (fine dust mask) and/or wet sandpaper. It's possible that the models are hollow. In this case, the model has drainage holes through which the liquid resin could leak out. The inside of the model was then also cured. Drainage holes can be closed with modelling putty. Resin is heat-sensitive and can therefore deform during the printing process, the removal of the support structures, post-process curing, or shipping. Hot water or a heat gun/hair dryer can quickly remedy this. The affected part is heated and then carefully bent into the correct position. Important noticeWarning! Not for children under the age of 3. Choking hazard due to small parts.This product is not a toy.

Swarm spaceship for collectors, painters and gamers, eg. for Battlefleet Gothic, Firestorm Armada, Full Thrust, A Billion Suns, Warfleets: FTL, Dropfleet Commander or other Science Fiction spaceship miniature wargames.Note: the ship is cruiser-sized. Please note that the models are supplied WITHOUT bases. The pictures show a digital render. The 3D files are from NofixedForge These 3D files are produced and sold under a commercial licence. Printed and painted model by NofixedForge. Most of the miniatures are printed after you order them. The long processing time allows me to sensibly plan my working and printing time. Whenever possible, I try to cut the processing time short. The models are delivered unpainted and unassambled. This is a 3D printed product made of UV hardened resin. Models are cleaned and completely cured with UV light. Before printing, a support structure needs to be added to the models, these are normally removed after printing, but leave "scars" on the model. These are production-related and do not represent a defect in the product. Remains of the support structure might still be on the model and can be removed with a sharp hobby knife. Resin dust is a health hazard if inhaled into the lungs. Sanding and filing is not recommended. Otherwise, such work should only be carried out with appropriate protective equipment (fine dust mask) and/or wet sandpaper. It's possible that the models are hollow. In this case, the model has drainage holes through which the liquid resin could leak out. The inside of the model was then also cured. Drainage holes can be closed with modelling putty. Resin is heat-sensitive and can therefore deform during the printing process, the removal of the support structures, post-process curing, or shipping. Hot water or a heat gun/hair dryer can quickly remedy this. The affected part is heated and then carefully bent into the correct position. Important noticeWarning! Not for children under the age of 3. Choking hazard due to small parts.This product is not a toy.

Swarm spaceship. For collectors, painters and gamers, eg. for Battlefleet Gothic, Firestorm Armada, Full Thrust, A Billion Suns, Warfleets: FTL, Dropfleet Commander or other Science Fiction spaceship miniature wargames. Please note that the models are supplied WITHOUT bases. The pictures show a digital render. The 3D files are from Baukloetzchen. These 3D files are produced and sold under a commercial licence. Most of the miniatures are printed after you order them. The long processing time allows me to sensibly plan my working and printing time. Whenever possible, I try to cut the processing time short. The models are delivered unpainted and unassambled. This is a 3D printed product made of UV hardened resin. Models are cleaned and completely cured with UV light. Before printing, a support structure needs to be added to the models, these are normally removed after printing, but leave "scars" on the model. These are production-related and do not represent a defect in the product. Remains of the support structure might still be on the model and can be removed with a sharp hobby knife. Resin dust is a health hazard if inhaled into the lungs. Sanding and filing is not recommended. Otherwise, such work should only be carried out with appropriate protective equipment (fine dust mask) and/or wet sandpaper. It's possible that the models are hollow. In this case, the model has drainage holes through which the liquid resin could leak out. The inside of the model was then also cured. Drainage holes can be closed with modelling putty. Resin is heat-sensitive and can therefore deform during the printing process, the removal of the support structures, post-process curing, or shipping. Hot water or a heat gun/hair dryer can quickly remedy this. The affected part is heated and then carefully bent into the correct position. Important noticeWarning! Not for children under the age of 3. Choking hazard due to small parts.This product is not a toy.

Swarm spaceship for collectors, painters and gamers, eg. for Battlefleet Gothic, Firestorm Armada, Full Thrust, A Billion Suns, Warfleets: FTL, Dropfleet Commander or other Science Fiction spaceship miniature wargames. Please note that the models are supplied WITHOUT bases. The pictures show a digital render. The 3D files are from NofixedForge These 3D files are produced and sold under a commercial licence. Printed and painted model by NofixedForge. Most of the miniatures are printed after you order them. The long processing time allows me to sensibly plan my working and printing time. Whenever possible, I try to cut the processing time short. The models are delivered unpainted and unassambled. This is a 3D printed product made of UV hardened resin. Models are cleaned and completely cured with UV light. Before printing, a support structure needs to be added to the models, these are normally removed after printing, but leave "scars" on the model. These are production-related and do not represent a defect in the product. Remains of the support structure might still be on the model and can be removed with a sharp hobby knife. Resin dust is a health hazard if inhaled into the lungs. Sanding and filing is not recommended. Otherwise, such work should only be carried out with appropriate protective equipment (fine dust mask) and/or wet sandpaper. It's possible that the models are hollow. In this case, the model has drainage holes through which the liquid resin could leak out. The inside of the model was then also cured. Drainage holes can be closed with modelling putty. Resin is heat-sensitive and can therefore deform during the printing process, the removal of the support structures, post-process curing, or shipping. Hot water or a heat gun/hair dryer can quickly remedy this. The affected part is heated and then carefully bent into the correct position. Important noticeWarning! Not for children under the age of 3. Choking hazard due to small parts.This product is not a toy.

Swarm spaceship. For collectors, painters and gamers, eg. for Battlefleet Gothic, Firestorm Armada, Full Thrust, A Billion Suns, Warfleets: FTL, Dropfleet Commander or other Science Fiction spaceship miniature wargames. Tentacle positions are picked randomly from 7 variations. Please note that the models are supplied WITHOUT bases. The pictures show a digital render. The 3D files are from Baukloetzchen. These 3D files are produced and sold under a commercial licence. Most of the miniatures are printed after you order them. The long processing time allows me to sensibly plan my working and printing time. Whenever possible, I try to cut the processing time short. The models are delivered unpainted and unassambled. This is a 3D printed product made of UV hardened resin. Models are cleaned and completely cured with UV light. Before printing, a support structure needs to be added to the models, these are normally removed after printing, but leave "scars" on the model. These are production-related and do not represent a defect in the product. Remains of the support structure might still be on the model and can be removed with a sharp hobby knife. Resin dust is a health hazard if inhaled into the lungs. Sanding and filing is not recommended. Otherwise, such work should only be carried out with appropriate protective equipment (fine dust mask) and/or wet sandpaper. It's possible that the models are hollow. In this case, the model has drainage holes through which the liquid resin could leak out. The inside of the model was then also cured. Drainage holes can be closed with modelling putty. Resin is heat-sensitive and can therefore deform during the printing process, the removal of the support structures, post-process curing, or shipping. Hot water or a heat gun/hair dryer can quickly remedy this. The affected part is heated and then carefully bent into the correct position. Important noticeWarning! Not for children under the age of 3. Choking hazard due to small parts.This product is not a toy.