28-32 mm Maßstab für Sammler, Maler und Spieler, z.B. für Warhammer Fantasy (Oger Königreiche), Age of Sigmar (Ogor Mawtribes), WarCry, Frostgrave, Dungeons & Dragons, oder sonstige Fantasy Tabletops und Rollenspiele.Die Modelle haben eine Höhe von ca. 28 mm bis zur Oberkante vom Turban.Please note that the models are supplied WITHOUT bases. The pictures show a digital render. The 3D files are from Ghamak. These 3D files are produced and sold under a commercial licence. Most of the miniatures are printed after you order them. The long processing time allows me to sensibly plan my working and printing time. Whenever possible, I try to cut the processing time short. The models are delivered unpainted and unassambled. This is a 3D printed product made of UV hardened resin. Models are cleaned and completely cured with UV light. Before printing, a support structure needs to be added to the models, these are normally removed after printing, but leave "scars" on the model. These are production-related and do not represent a defect in the product. Remains of the support structure might still be on the model and can be removed with a sharp hobby knife. Resin dust is a health hazard if inhaled into the lungs. Sanding and filing is not recommended. Otherwise, such work should only be carried out with appropriate protective equipment (fine dust mask) and/or wet sandpaper. It's possible that the models are hollow. In this case, the model has drainage holes through which the liquid resin could leak out. The inside of the model was then also cured. Drainage holes can be closed with modelling putty. Resin is heat-sensitive and can therefore deform during the printing process, the removal of the support structures, post-process curing, or shipping. Hot water or a heat gun/hair dryer can quickly remedy this. The affected part is heated and then carefully bent into the correct position. Important noticeWarning! Not for children under the age of 3. Choking hazard due to small parts.This product is not a toy.

28-32 mm Maßstab für Sammler, Maler und Spieler, z.B. für Warhammer Fantasy (Oger Königreiche), Age of Sigmar (Ogor Mawtribes), WarCry, Frostgrave, Dungeons & Dragons, oder sonstige Fantasy Tabletops und Rollenspiele.Das Modell hat eine Höhe von ca. 54 mm bis zur Oberkante vom Kopf.Please note that the models are supplied WITHOUT bases. The pictures show a digital render. The 3D files are from Ghamak. These 3D files are produced and sold under a commercial licence. Most of the miniatures are printed after you order them. The long processing time allows me to sensibly plan my working and printing time. Whenever possible, I try to cut the processing time short. The models are delivered unpainted and unassambled. This is a 3D printed product made of UV hardened resin. Models are cleaned and completely cured with UV light. Before printing, a support structure needs to be added to the models, these are normally removed after printing, but leave "scars" on the model. These are production-related and do not represent a defect in the product. Remains of the support structure might still be on the model and can be removed with a sharp hobby knife. Resin dust is a health hazard if inhaled into the lungs. Sanding and filing is not recommended. Otherwise, such work should only be carried out with appropriate protective equipment (fine dust mask) and/or wet sandpaper. It's possible that the models are hollow. In this case, the model has drainage holes through which the liquid resin could leak out. The inside of the model was then also cured. Drainage holes can be closed with modelling putty. Resin is heat-sensitive and can therefore deform during the printing process, the removal of the support structures, post-process curing, or shipping. Hot water or a heat gun/hair dryer can quickly remedy this. The affected part is heated and then carefully bent into the correct position. Important noticeWarning! Not for children under the age of 3. Choking hazard due to small parts.This product is not a toy.

28-32 mm Maßstab für Sammler, Maler und Spieler, z.B. für Warhammer Fantasy (Oger Königreiche), Age of Sigmar (Ogor Mawtribes), WarCry, Frostgrave, Dungeons & Dragons, oder sonstige Fantasy Tabletops und Rollenspiele.Die Modelle haben eine Höhe von ca. 50 mm bis zur Oberkante vom Kopf.Please note that the models are supplied WITHOUT bases. The pictures show a digital render. The 3D files are from Ghamak. These 3D files are produced and sold under a commercial licence. Most of the miniatures are printed after you order them. The long processing time allows me to sensibly plan my working and printing time. Whenever possible, I try to cut the processing time short. The models are delivered unpainted and unassambled. This is a 3D printed product made of UV hardened resin. Models are cleaned and completely cured with UV light. Before printing, a support structure needs to be added to the models, these are normally removed after printing, but leave "scars" on the model. These are production-related and do not represent a defect in the product. Remains of the support structure might still be on the model and can be removed with a sharp hobby knife. Resin dust is a health hazard if inhaled into the lungs. Sanding and filing is not recommended. Otherwise, such work should only be carried out with appropriate protective equipment (fine dust mask) and/or wet sandpaper. It's possible that the models are hollow. In this case, the model has drainage holes through which the liquid resin could leak out. The inside of the model was then also cured. Drainage holes can be closed with modelling putty. Resin is heat-sensitive and can therefore deform during the printing process, the removal of the support structures, post-process curing, or shipping. Hot water or a heat gun/hair dryer can quickly remedy this. The affected part is heated and then carefully bent into the correct position. Important noticeWarning! Not for children under the age of 3. Choking hazard due to small parts.This product is not a toy.

28-32 mm Maßstab für Sammler, Maler und Spieler, z.B. für Warhammer Fantasy (Oger Königreiche), Age of Sigmar (Ogor Mawtribes), WarCry, Frostgrave, Dungeons & Dragons, oder sonstige Fantasy Tabletops und Rollenspiele.Ihr erhaltet einen Oger mit Standarte und einen mit Harfen. Das Set ergänzt die Hippo Cavalry zu einer kompletten 4er Einheit.Die Modelle haben eine Höhe von ca. 90 mm bis zur Oberkante vom Kopf.Please note that the models are supplied WITHOUT bases. The pictures show a digital render. The 3D files are from Ghamak. These 3D files are produced and sold under a commercial licence. Most of the miniatures are printed after you order them. The long processing time allows me to sensibly plan my working and printing time. Whenever possible, I try to cut the processing time short. The models are delivered unpainted and unassambled. This is a 3D printed product made of UV hardened resin. Models are cleaned and completely cured with UV light. Before printing, a support structure needs to be added to the models, these are normally removed after printing, but leave "scars" on the model. These are production-related and do not represent a defect in the product. Remains of the support structure might still be on the model and can be removed with a sharp hobby knife. Resin dust is a health hazard if inhaled into the lungs. Sanding and filing is not recommended. Otherwise, such work should only be carried out with appropriate protective equipment (fine dust mask) and/or wet sandpaper. It's possible that the models are hollow. In this case, the model has drainage holes through which the liquid resin could leak out. The inside of the model was then also cured. Drainage holes can be closed with modelling putty. Resin is heat-sensitive and can therefore deform during the printing process, the removal of the support structures, post-process curing, or shipping. Hot water or a heat gun/hair dryer can quickly remedy this. The affected part is heated and then carefully bent into the correct position. Important noticeWarning! Not for children under the age of 3. Choking hazard due to small parts.This product is not a toy.

28-32 mm Maßstab für Sammler, Maler und Spieler, z.B. für Warhammer Fantasy (Oger Königreiche), Age of Sigmar (Ogor Mawtribes), WarCry, Frostgrave, Dungeons & Dragons, oder sonstige Fantasy Tabletops und Rollenspiele.Das Modell hat eine Augenhöhe von ca. 31 mm.Please note that the models are supplied WITHOUT bases. The pictures show a digital render. The 3D files are from Ghamak. These 3D files are produced and sold under a commercial licence. Most of the miniatures are printed after you order them. The long processing time allows me to sensibly plan my working and printing time. Whenever possible, I try to cut the processing time short. The models are delivered unpainted and unassambled. This is a 3D printed product made of UV hardened resin. Models are cleaned and completely cured with UV light. Before printing, a support structure needs to be added to the models, these are normally removed after printing, but leave "scars" on the model. These are production-related and do not represent a defect in the product. Remains of the support structure might still be on the model and can be removed with a sharp hobby knife. Resin dust is a health hazard if inhaled into the lungs. Sanding and filing is not recommended. Otherwise, such work should only be carried out with appropriate protective equipment (fine dust mask) and/or wet sandpaper. It's possible that the models are hollow. In this case, the model has drainage holes through which the liquid resin could leak out. The inside of the model was then also cured. Drainage holes can be closed with modelling putty. Resin is heat-sensitive and can therefore deform during the printing process, the removal of the support structures, post-process curing, or shipping. Hot water or a heat gun/hair dryer can quickly remedy this. The affected part is heated and then carefully bent into the correct position. Important noticeWarning! Not for children under the age of 3. Choking hazard due to small parts.This product is not a toy.

28-32 mm Maßstab für Sammler, Maler und Spieler, z.B. für Warhammer Fantasy (Oger Königreiche), Age of Sigmar (Ogor Mawtribes), WarCry, Frostgrave, Dungeons & Dragons, oder sonstige Fantasy Tabletops und Rollenspiele.Das Modell hat eine Höhe von ca. 65 mm und passt mit den Füßen auf eine 50 mm Base.Please note that the models are supplied WITHOUT bases. The pictures show a digital render. The 3D files are from Ghamak. These 3D files are produced and sold under a commercial licence. Most of the miniatures are printed after you order them. The long processing time allows me to sensibly plan my working and printing time. Whenever possible, I try to cut the processing time short. The models are delivered unpainted and unassambled. This is a 3D printed product made of UV hardened resin. Models are cleaned and completely cured with UV light. Before printing, a support structure needs to be added to the models, these are normally removed after printing, but leave "scars" on the model. These are production-related and do not represent a defect in the product. Remains of the support structure might still be on the model and can be removed with a sharp hobby knife. Resin dust is a health hazard if inhaled into the lungs. Sanding and filing is not recommended. Otherwise, such work should only be carried out with appropriate protective equipment (fine dust mask) and/or wet sandpaper. It's possible that the models are hollow. In this case, the model has drainage holes through which the liquid resin could leak out. The inside of the model was then also cured. Drainage holes can be closed with modelling putty. Resin is heat-sensitive and can therefore deform during the printing process, the removal of the support structures, post-process curing, or shipping. Hot water or a heat gun/hair dryer can quickly remedy this. The affected part is heated and then carefully bent into the correct position. Important noticeWarning! Not for children under the age of 3. Choking hazard due to small parts.This product is not a toy.

28-32 mm Maßstab für Sammler, Maler und Spieler, z.B. für Warhammer Fantasy (Oger Königreiche), Age of Sigmar (Ogor Mawtribes), WarCry, Frostgrave, Dungeons & Dragons, oder sonstige Fantasy Tabletops und Rollenspiele.Ihr erhaltet Anführer (Zweihandaxt), Hornbläser, Standartenträger und einen zufälligen der anderen zwei Oger (Hammer und Schwert) um eine volle 4er Einheit zu spielen.Die Modelle haben eine Höhe von ca. 50 mm bis zur Oberkante vom Kopf.Please note that the models are supplied WITHOUT bases. The pictures show a digital render. The 3D files are from Ghamak. These 3D files are produced and sold under a commercial licence. Most of the miniatures are printed after you order them. The long processing time allows me to sensibly plan my working and printing time. Whenever possible, I try to cut the processing time short. The models are delivered unpainted and unassambled. This is a 3D printed product made of UV hardened resin. Models are cleaned and completely cured with UV light. Before printing, a support structure needs to be added to the models, these are normally removed after printing, but leave "scars" on the model. These are production-related and do not represent a defect in the product. Remains of the support structure might still be on the model and can be removed with a sharp hobby knife. Resin dust is a health hazard if inhaled into the lungs. Sanding and filing is not recommended. Otherwise, such work should only be carried out with appropriate protective equipment (fine dust mask) and/or wet sandpaper. It's possible that the models are hollow. In this case, the model has drainage holes through which the liquid resin could leak out. The inside of the model was then also cured. Drainage holes can be closed with modelling putty. Resin is heat-sensitive and can therefore deform during the printing process, the removal of the support structures, post-process curing, or shipping. Hot water or a heat gun/hair dryer can quickly remedy this. The affected part is heated and then carefully bent into the correct position. Important noticeWarning! Not for children under the age of 3. Choking hazard due to small parts.This product is not a toy.

28-32 mm Maßstab für Sammler, Maler und Spieler, z.B. für Warhammer Fantasy (Oger Königreiche), Age of Sigmar (Ogor Mawtribes), WarCry, Frostgrave, Dungeons & Dragons, oder sonstige Fantasy Tabletops und Rollenspiele.Das Modell hat eine Höhe von ca. 60 mm bis zur Oberkante vom Turban.Please note that the models are supplied WITHOUT bases. The pictures show a digital render. The 3D files are from Ghamak. These 3D files are produced and sold under a commercial licence. Most of the miniatures are printed after you order them. The long processing time allows me to sensibly plan my working and printing time. Whenever possible, I try to cut the processing time short. The models are delivered unpainted and unassambled. This is a 3D printed product made of UV hardened resin. Models are cleaned and completely cured with UV light. Before printing, a support structure needs to be added to the models, these are normally removed after printing, but leave "scars" on the model. These are production-related and do not represent a defect in the product. Remains of the support structure might still be on the model and can be removed with a sharp hobby knife. Resin dust is a health hazard if inhaled into the lungs. Sanding and filing is not recommended. Otherwise, such work should only be carried out with appropriate protective equipment (fine dust mask) and/or wet sandpaper. It's possible that the models are hollow. In this case, the model has drainage holes through which the liquid resin could leak out. The inside of the model was then also cured. Drainage holes can be closed with modelling putty. Resin is heat-sensitive and can therefore deform during the printing process, the removal of the support structures, post-process curing, or shipping. Hot water or a heat gun/hair dryer can quickly remedy this. The affected part is heated and then carefully bent into the correct position. Important noticeWarning! Not for children under the age of 3. Choking hazard due to small parts.This product is not a toy.

28-32 mm Maßstab für Sammler, Maler und Spieler, z.B. für Warhammer Fantasy (Oger Königreiche), Age of Sigmar (Ogor Mawtribes), WarCry, Frostgrave, Dungeons & Dragons, oder sonstige Fantasy Tabletops und Rollenspiele.Das Modell hat eine Höhe von ca. 65 mm bis zur Oberkante vom Turban.Please note that the models are supplied WITHOUT bases. The pictures show a digital render. The 3D files are from Ghamak. These 3D files are produced and sold under a commercial licence. Most of the miniatures are printed after you order them. The long processing time allows me to sensibly plan my working and printing time. Whenever possible, I try to cut the processing time short. The models are delivered unpainted and unassambled. This is a 3D printed product made of UV hardened resin. Models are cleaned and completely cured with UV light. Before printing, a support structure needs to be added to the models, these are normally removed after printing, but leave "scars" on the model. These are production-related and do not represent a defect in the product. Remains of the support structure might still be on the model and can be removed with a sharp hobby knife. Resin dust is a health hazard if inhaled into the lungs. Sanding and filing is not recommended. Otherwise, such work should only be carried out with appropriate protective equipment (fine dust mask) and/or wet sandpaper. It's possible that the models are hollow. In this case, the model has drainage holes through which the liquid resin could leak out. The inside of the model was then also cured. Drainage holes can be closed with modelling putty. Resin is heat-sensitive and can therefore deform during the printing process, the removal of the support structures, post-process curing, or shipping. Hot water or a heat gun/hair dryer can quickly remedy this. The affected part is heated and then carefully bent into the correct position. Important noticeWarning! Not for children under the age of 3. Choking hazard due to small parts.This product is not a toy.

28-32 mm Maßstab für Sammler, Maler und Spieler, z.B. für Warhammer Fantasy (Oger Königreiche), Age of Sigmar (Ogor Mawtribes), WarCry, Frostgrave, Dungeons & Dragons, oder sonstige Fantasy Tabletops und Rollenspiele.Die Modelle haben eine Höhe von ca. 50 mm.Please note that the models are supplied WITHOUT bases. The pictures show a digital render. The 3D files are from Ghamak. These 3D files are produced and sold under a commercial licence. Most of the miniatures are printed after you order them. The long processing time allows me to sensibly plan my working and printing time. Whenever possible, I try to cut the processing time short. The models are delivered unpainted and unassambled. This is a 3D printed product made of UV hardened resin. Models are cleaned and completely cured with UV light. Before printing, a support structure needs to be added to the models, these are normally removed after printing, but leave "scars" on the model. These are production-related and do not represent a defect in the product. Remains of the support structure might still be on the model and can be removed with a sharp hobby knife. Resin dust is a health hazard if inhaled into the lungs. Sanding and filing is not recommended. Otherwise, such work should only be carried out with appropriate protective equipment (fine dust mask) and/or wet sandpaper. It's possible that the models are hollow. In this case, the model has drainage holes through which the liquid resin could leak out. The inside of the model was then also cured. Drainage holes can be closed with modelling putty. Resin is heat-sensitive and can therefore deform during the printing process, the removal of the support structures, post-process curing, or shipping. Hot water or a heat gun/hair dryer can quickly remedy this. The affected part is heated and then carefully bent into the correct position. Important noticeWarning! Not for children under the age of 3. Choking hazard due to small parts.This product is not a toy.

28-32 mm Maßstab für Sammler, Maler und Spieler, z.B. für Warhammer Fantasy (Oger Königreiche), Age of Sigmar (Ogor Mawtribes), WarCry, Frostgrave, Dungeons & Dragons, oder sonstige Fantasy Tabletops und Rollenspiele.Die Modelle haben eine Höhe von ca. 50 mm bis zur Oberkante vom Kopf.Please note that the models are supplied WITHOUT bases. The pictures show a digital render. The 3D files are from Ghamak. These 3D files are produced and sold under a commercial licence. Most of the miniatures are printed after you order them. The long processing time allows me to sensibly plan my working and printing time. Whenever possible, I try to cut the processing time short. The models are delivered unpainted and unassambled. This is a 3D printed product made of UV hardened resin. Models are cleaned and completely cured with UV light. Before printing, a support structure needs to be added to the models, these are normally removed after printing, but leave "scars" on the model. These are production-related and do not represent a defect in the product. Remains of the support structure might still be on the model and can be removed with a sharp hobby knife. Resin dust is a health hazard if inhaled into the lungs. Sanding and filing is not recommended. Otherwise, such work should only be carried out with appropriate protective equipment (fine dust mask) and/or wet sandpaper. It's possible that the models are hollow. In this case, the model has drainage holes through which the liquid resin could leak out. The inside of the model was then also cured. Drainage holes can be closed with modelling putty. Resin is heat-sensitive and can therefore deform during the printing process, the removal of the support structures, post-process curing, or shipping. Hot water or a heat gun/hair dryer can quickly remedy this. The affected part is heated and then carefully bent into the correct position. Important noticeWarning! Not for children under the age of 3. Choking hazard due to small parts.This product is not a toy.

28-32 mm Maßstab für Sammler, Maler und Spieler, z.B. für Warhammer Fantasy (Oger Königreiche), Age of Sigmar (Ogor Mawtribes), WarCry, Frostgrave, Dungeons & Dragons, oder sonstige Fantasy Tabletops und Rollenspiele.Aus insgesamt fünf verschiedenen Modelle erhaltet ihr zufällig zwei Modelle.Please note that the models are supplied WITHOUT bases. The pictures show a digital render. The 3D files are from Ghamak. These 3D files are produced and sold under a commercial licence. Most of the miniatures are printed after you order them. The long processing time allows me to sensibly plan my working and printing time. Whenever possible, I try to cut the processing time short. The models are delivered unpainted and unassambled. This is a 3D printed product made of UV hardened resin. Models are cleaned and completely cured with UV light. Before printing, a support structure needs to be added to the models, these are normally removed after printing, but leave "scars" on the model. These are production-related and do not represent a defect in the product. Remains of the support structure might still be on the model and can be removed with a sharp hobby knife. Resin dust is a health hazard if inhaled into the lungs. Sanding and filing is not recommended. Otherwise, such work should only be carried out with appropriate protective equipment (fine dust mask) and/or wet sandpaper. It's possible that the models are hollow. In this case, the model has drainage holes through which the liquid resin could leak out. The inside of the model was then also cured. Drainage holes can be closed with modelling putty. Resin is heat-sensitive and can therefore deform during the printing process, the removal of the support structures, post-process curing, or shipping. Hot water or a heat gun/hair dryer can quickly remedy this. The affected part is heated and then carefully bent into the correct position. Important noticeWarning! Not for children under the age of 3. Choking hazard due to small parts.This product is not a toy.