Filter
–
Conversion Kit: Desert Skeleton Weapons (20 pcs)
32 mm scale, conversion kit for old plastik kits from the 90s. You may have to do small adjustments on the shoulder joint. Please note that the proportions of these parts are more realistic than some other manufacturers. A random selection of parts is made. Please note that the models are supplied WITHOUT bases. The pictures show a digital render.The 3D files are from Crab Miniatures. These 3D files are produced and sold under a commercial licence. Most of the miniatures are printed after you order them. The long processing time allows me to sensibly plan my working and printing time. Whenever possible, I try to cut the processing time short. The models are delivered unpainted and unassambled. This is a 3D printed product made of UV hardened resin. Models are cleaned and completely cured with UV light. Before printing, a support structure needs to be added to the models, these are normally removed after printing, but leave "scars" on the model. These are production-related and do not represent a defect in the product. Remains of the support structure might still be on the model and can be removed with a sharp hobby knife. Resin dust is a health hazard if inhaled into the lungs. Sanding and filing is not recommended. Otherwise, such work should only be carried out with appropriate protective equipment (fine dust mask) and/or wet sandpaper. It's possible that the models are hollow. In this case, the model has drainage holes through which the liquid resin could leak out. The inside of the model was then also cured. Drainage holes can be closed with modelling putty. Resin is heat-sensitive and can therefore deform during the printing process, the removal of the support structures, post-process curing, or shipping. Hot water or a heat gun/hair dryer can quickly remedy this. The affected part is heated and then carefully bent into the correct position. Important noticeWarning! Not for children under the age of 3. Choking hazard due to small parts.This product is not a toy.
€8.50*
Desert Chamberlain
Fantasy mass battle system compatible models, like e.g. Warhammer Fantasy, The Old World, Age of Sigmar, Kings of War, Oathmark, Dragon Rampant, or other fantasy miniature wargames. Scale as chosen. Please see the size comparison picture for which scale is right for you. Please note that the models are supplied WITHOUT bases. The pictures show a digital render.The 3D files are from Crab Miniatures. These 3D files are produced and sold under a commercial licence. Most of the miniatures are printed after you order them. The long processing time allows me to sensibly plan my working and printing time. Whenever possible, I try to cut the processing time short. The models are delivered unpainted and unassambled. This is a 3D printed product made of UV hardened resin. Models are cleaned and completely cured with UV light. Before printing, a support structure needs to be added to the models, these are normally removed after printing, but leave "scars" on the model. These are production-related and do not represent a defect in the product. Remains of the support structure might still be on the model and can be removed with a sharp hobby knife. Resin dust is a health hazard if inhaled into the lungs. Sanding and filing is not recommended. Otherwise, such work should only be carried out with appropriate protective equipment (fine dust mask) and/or wet sandpaper. It's possible that the models are hollow. In this case, the model has drainage holes through which the liquid resin could leak out. The inside of the model was then also cured. Drainage holes can be closed with modelling putty. Resin is heat-sensitive and can therefore deform during the printing process, the removal of the support structures, post-process curing, or shipping. Hot water or a heat gun/hair dryer can quickly remedy this. The affected part is heated and then carefully bent into the correct position. Important noticeWarning! Not for children under the age of 3. Choking hazard due to small parts.This product is not a toy.
€7.00*
Desert Skeleton Archers (10 models)
Fantasy mass battle system compatible models, like e.g. Warhammer Fantasy, The Old World, Age of Sigmar, Kings of War, Oathmark, Dragon Rampant, or other fantasy miniature wargames. Scale as chosen. Please see the size comparison picture for which scale is right for you. The models are one piece each. Please note that the models are supplied WITHOUT bases. The pictures show a digital render.The 3D files are from Crab Miniatures. These 3D files are produced and sold under a commercial licence. Most of the miniatures are printed after you order them. The long processing time allows me to sensibly plan my working and printing time. Whenever possible, I try to cut the processing time short. The models are delivered unpainted and unassambled. This is a 3D printed product made of UV hardened resin. Models are cleaned and completely cured with UV light. Before printing, a support structure needs to be added to the models, these are normally removed after printing, but leave "scars" on the model. These are production-related and do not represent a defect in the product. Remains of the support structure might still be on the model and can be removed with a sharp hobby knife. Resin dust is a health hazard if inhaled into the lungs. Sanding and filing is not recommended. Otherwise, such work should only be carried out with appropriate protective equipment (fine dust mask) and/or wet sandpaper. It's possible that the models are hollow. In this case, the model has drainage holes through which the liquid resin could leak out. The inside of the model was then also cured. Drainage holes can be closed with modelling putty. Resin is heat-sensitive and can therefore deform during the printing process, the removal of the support structures, post-process curing, or shipping. Hot water or a heat gun/hair dryer can quickly remedy this. The affected part is heated and then carefully bent into the correct position. Important noticeWarning! Not for children under the age of 3. Choking hazard due to small parts.This product is not a toy.
€18.00*
Desert Skeleton Archers (16 models)
Fantasy mass battle system compatible models, like e.g. Warhammer Fantasy, The Old World, Age of Sigmar, Kings of War, Oathmark, Dragon Rampant, or other fantasy miniature wargames. Scale as chosen. Please see the size comparison picture for which scale is right for you. The models are one piece each.A random selection of parts is made, but extra care is taken that it is balanced and duplicates are kept to a minimum. Please note that the models are supplied WITHOUT bases. The pictures show a digital render.The 3D files are from Crab Miniatures. These 3D files are produced and sold under a commercial licence. Most of the miniatures are printed after you order them. The long processing time allows me to sensibly plan my working and printing time. Whenever possible, I try to cut the processing time short. The models are delivered unpainted and unassambled. This is a 3D printed product made of UV hardened resin. Models are cleaned and completely cured with UV light. Before printing, a support structure needs to be added to the models, these are normally removed after printing, but leave "scars" on the model. These are production-related and do not represent a defect in the product. Remains of the support structure might still be on the model and can be removed with a sharp hobby knife. Resin dust is a health hazard if inhaled into the lungs. Sanding and filing is not recommended. Otherwise, such work should only be carried out with appropriate protective equipment (fine dust mask) and/or wet sandpaper. It's possible that the models are hollow. In this case, the model has drainage holes through which the liquid resin could leak out. The inside of the model was then also cured. Drainage holes can be closed with modelling putty. Resin is heat-sensitive and can therefore deform during the printing process, the removal of the support structures, post-process curing, or shipping. Hot water or a heat gun/hair dryer can quickly remedy this. The affected part is heated and then carefully bent into the correct position. Important noticeWarning! Not for children under the age of 3. Choking hazard due to small parts.This product is not a toy.
€25.00*
Desert Skeleton Archers (Modular | 10 models)
Fantasy mass battle system compatible models, like e.g. Warhammer Fantasy, The Old World, Age of Sigmar, Kings of War, Oathmark, Dragon Rampant, or other fantasy miniature wargames. Scale as chosen. Please see the size comparison picture for which scale is right for you. A random selection of parts is made, but extra care is taken that it is balanced and duplicates are kept to a minimum. Please note that the models are supplied WITHOUT bases. The pictures show a digital render.The 3D files are from Crab Miniatures. These 3D files are produced and sold under a commercial licence. Most of the miniatures are printed after you order them. The long processing time allows me to sensibly plan my working and printing time. Whenever possible, I try to cut the processing time short. The models are delivered unpainted and unassambled. This is a 3D printed product made of UV hardened resin. Models are cleaned and completely cured with UV light. Before printing, a support structure needs to be added to the models, these are normally removed after printing, but leave "scars" on the model. These are production-related and do not represent a defect in the product. Remains of the support structure might still be on the model and can be removed with a sharp hobby knife. Resin dust is a health hazard if inhaled into the lungs. Sanding and filing is not recommended. Otherwise, such work should only be carried out with appropriate protective equipment (fine dust mask) and/or wet sandpaper. It's possible that the models are hollow. In this case, the model has drainage holes through which the liquid resin could leak out. The inside of the model was then also cured. Drainage holes can be closed with modelling putty. Resin is heat-sensitive and can therefore deform during the printing process, the removal of the support structures, post-process curing, or shipping. Hot water or a heat gun/hair dryer can quickly remedy this. The affected part is heated and then carefully bent into the correct position. Important noticeWarning! Not for children under the age of 3. Choking hazard due to small parts.This product is not a toy.
€20.00*
Desert Skeleton Archers (Modular | 16 models)
Fantasy mass battle system compatible models, like e.g. Warhammer Fantasy, The Old World, Age of Sigmar, Kings of War, Oathmark, Dragon Rampant, or other fantasy miniature wargames. Scale as chosen. Please see the size comparison picture for which scale is right for you. A random selection of parts is made, but extra care is taken that it is balanced and duplicates are kept to a minimum. Please note that the models are supplied WITHOUT bases. The pictures show a digital render.The 3D files are from Crab Miniatures. These 3D files are produced and sold under a commercial licence. Most of the miniatures are printed after you order them. The long processing time allows me to sensibly plan my working and printing time. Whenever possible, I try to cut the processing time short. The models are delivered unpainted and unassambled. This is a 3D printed product made of UV hardened resin. Models are cleaned and completely cured with UV light. Before printing, a support structure needs to be added to the models, these are normally removed after printing, but leave "scars" on the model. These are production-related and do not represent a defect in the product. Remains of the support structure might still be on the model and can be removed with a sharp hobby knife. Resin dust is a health hazard if inhaled into the lungs. Sanding and filing is not recommended. Otherwise, such work should only be carried out with appropriate protective equipment (fine dust mask) and/or wet sandpaper. It's possible that the models are hollow. In this case, the model has drainage holes through which the liquid resin could leak out. The inside of the model was then also cured. Drainage holes can be closed with modelling putty. Resin is heat-sensitive and can therefore deform during the printing process, the removal of the support structures, post-process curing, or shipping. Hot water or a heat gun/hair dryer can quickly remedy this. The affected part is heated and then carefully bent into the correct position. Important noticeWarning! Not for children under the age of 3. Choking hazard due to small parts.This product is not a toy.
€31.00*
Desert Skeleton Battle Standard
Fantasy mass battle system compatible models, like e.g. Warhammer Fantasy, The Old World, Age of Sigmar, Kings of War, Oathmark, Dragon Rampant, or other fantasy miniature wargames. Scale as chosen. Please see the size comparison picture for which scale is right for you. Please note that the models are supplied WITHOUT bases. The pictures show a digital render.The 3D files are from Crab Miniatures. These 3D files are produced and sold under a commercial licence. Most of the miniatures are printed after you order them. The long processing time allows me to sensibly plan my working and printing time. Whenever possible, I try to cut the processing time short. The models are delivered unpainted and unassambled. This is a 3D printed product made of UV hardened resin. Models are cleaned and completely cured with UV light. Before printing, a support structure needs to be added to the models, these are normally removed after printing, but leave "scars" on the model. These are production-related and do not represent a defect in the product. Remains of the support structure might still be on the model and can be removed with a sharp hobby knife. Resin dust is a health hazard if inhaled into the lungs. Sanding and filing is not recommended. Otherwise, such work should only be carried out with appropriate protective equipment (fine dust mask) and/or wet sandpaper. It's possible that the models are hollow. In this case, the model has drainage holes through which the liquid resin could leak out. The inside of the model was then also cured. Drainage holes can be closed with modelling putty. Resin is heat-sensitive and can therefore deform during the printing process, the removal of the support structures, post-process curing, or shipping. Hot water or a heat gun/hair dryer can quickly remedy this. The affected part is heated and then carefully bent into the correct position. Important noticeWarning! Not for children under the age of 3. Choking hazard due to small parts.This product is not a toy.
€9.00*
Desert Skeleton Catapult
Fantasy mass battle system compatible models, like e.g. Warhammer Fantasy, The Old World, Age of Sigmar, Kings of War, Oathmark, Dragon Rampant, or other fantasy miniature wargames. Scale as chosen. Please see the size comparison picture for which scale is right for you. Please note that the models are supplied WITHOUT bases. The pictures show a digital render.The 3D files are from Crab Miniatures. These 3D files are produced and sold under a commercial licence. Most of the miniatures are printed after you order them. The long processing time allows me to sensibly plan my working and printing time. Whenever possible, I try to cut the processing time short. The models are delivered unpainted and unassambled. This is a 3D printed product made of UV hardened resin. Models are cleaned and completely cured with UV light. Before printing, a support structure needs to be added to the models, these are normally removed after printing, but leave "scars" on the model. These are production-related and do not represent a defect in the product. Remains of the support structure might still be on the model and can be removed with a sharp hobby knife. Resin dust is a health hazard if inhaled into the lungs. Sanding and filing is not recommended. Otherwise, such work should only be carried out with appropriate protective equipment (fine dust mask) and/or wet sandpaper. It's possible that the models are hollow. In this case, the model has drainage holes through which the liquid resin could leak out. The inside of the model was then also cured. Drainage holes can be closed with modelling putty. Resin is heat-sensitive and can therefore deform during the printing process, the removal of the support structures, post-process curing, or shipping. Hot water or a heat gun/hair dryer can quickly remedy this. The affected part is heated and then carefully bent into the correct position. Important noticeWarning! Not for children under the age of 3. Choking hazard due to small parts.This product is not a toy.
€35.00*
Desert Skeleton Cavalry (5 models)
Fantasy mass battle system compatible models, like e.g. Warhammer Fantasy, The Old World, Age of Sigmar, Kings of War, Oathmark, Dragon Rampant, or other fantasy miniature wargames. Scale as chosen. Please see the size comparison picture for which scale is right for you. A random selection of parts is made.Selecting the Command Group replaces 3 normal models. Please note that the models are supplied WITHOUT bases. The pictures show a digital render.The 3D files are from Crab Miniatures. These 3D files are produced and sold under a commercial licence. Most of the miniatures are printed after you order them. The long processing time allows me to sensibly plan my working and printing time. Whenever possible, I try to cut the processing time short. The models are delivered unpainted and unassambled. This is a 3D printed product made of UV hardened resin. Models are cleaned and completely cured with UV light. Before printing, a support structure needs to be added to the models, these are normally removed after printing, but leave "scars" on the model. These are production-related and do not represent a defect in the product. Remains of the support structure might still be on the model and can be removed with a sharp hobby knife. Resin dust is a health hazard if inhaled into the lungs. Sanding and filing is not recommended. Otherwise, such work should only be carried out with appropriate protective equipment (fine dust mask) and/or wet sandpaper. It's possible that the models are hollow. In this case, the model has drainage holes through which the liquid resin could leak out. The inside of the model was then also cured. Drainage holes can be closed with modelling putty. Resin is heat-sensitive and can therefore deform during the printing process, the removal of the support structures, post-process curing, or shipping. Hot water or a heat gun/hair dryer can quickly remedy this. The affected part is heated and then carefully bent into the correct position. Important noticeWarning! Not for children under the age of 3. Choking hazard due to small parts.This product is not a toy.
€25.00*
Desert Skeleton Cavalry (8 models)
Fantasy mass battle system compatible models, like e.g. Warhammer Fantasy, The Old World, Age of Sigmar, Kings of War, Oathmark, Dragon Rampant, or other fantasy miniature wargames. Scale as chosen. Please see the size comparison picture for which scale is right for you. A random selection of parts is made, but extra care is taken that it is balanced and duplicates are kept to a minimum.Selecting the Command Group replaces 3 normal models. Please note that the models are supplied WITHOUT bases. The pictures show a digital render.The 3D files are from Crab Miniatures. These 3D files are produced and sold under a commercial licence. Most of the miniatures are printed after you order them. The long processing time allows me to sensibly plan my working and printing time. Whenever possible, I try to cut the processing time short. The models are delivered unpainted and unassambled. This is a 3D printed product made of UV hardened resin. Models are cleaned and completely cured with UV light. Before printing, a support structure needs to be added to the models, these are normally removed after printing, but leave "scars" on the model. These are production-related and do not represent a defect in the product. Remains of the support structure might still be on the model and can be removed with a sharp hobby knife. Resin dust is a health hazard if inhaled into the lungs. Sanding and filing is not recommended. Otherwise, such work should only be carried out with appropriate protective equipment (fine dust mask) and/or wet sandpaper. It's possible that the models are hollow. In this case, the model has drainage holes through which the liquid resin could leak out. The inside of the model was then also cured. Drainage holes can be closed with modelling putty. Resin is heat-sensitive and can therefore deform during the printing process, the removal of the support structures, post-process curing, or shipping. Hot water or a heat gun/hair dryer can quickly remedy this. The affected part is heated and then carefully bent into the correct position. Important noticeWarning! Not for children under the age of 3. Choking hazard due to small parts.This product is not a toy.
€38.00*
Desert Skeleton Chariots (3 models)
Fantasy mass battle system compatible models, like e.g. Warhammer Fantasy, The Old World, Age of Sigmar, Kings of War, Oathmark, Dragon Rampant, or other fantasy miniature wargames. Scale as chosen. Please see the size comparison picture for which scale is right for you. A random selection of parts is made.Selecting the Command Group replaces parts for 3 (of 6) of the normal skeletons. Please note that the models are supplied WITHOUT bases. The pictures show a digital render.The 3D files are from Crab Miniatures. These 3D files are produced and sold under a commercial licence. Most of the miniatures are printed after you order them. The long processing time allows me to sensibly plan my working and printing time. Whenever possible, I try to cut the processing time short. The models are delivered unpainted and unassambled. This is a 3D printed product made of UV hardened resin. Models are cleaned and completely cured with UV light. Before printing, a support structure needs to be added to the models, these are normally removed after printing, but leave "scars" on the model. These are production-related and do not represent a defect in the product. Remains of the support structure might still be on the model and can be removed with a sharp hobby knife. Resin dust is a health hazard if inhaled into the lungs. Sanding and filing is not recommended. Otherwise, such work should only be carried out with appropriate protective equipment (fine dust mask) and/or wet sandpaper. It's possible that the models are hollow. In this case, the model has drainage holes through which the liquid resin could leak out. The inside of the model was then also cured. Drainage holes can be closed with modelling putty. Resin is heat-sensitive and can therefore deform during the printing process, the removal of the support structures, post-process curing, or shipping. Hot water or a heat gun/hair dryer can quickly remedy this. The affected part is heated and then carefully bent into the correct position. Important noticeWarning! Not for children under the age of 3. Choking hazard due to small parts.This product is not a toy.
€38.00*
Desert Skeleton Guardians (3 models)
Fantasy mass battle system compatible models, like e.g. Warhammer Fantasy, The Old World, Age of Sigmar, Kings of War, Oathmark, Dragon Rampant, or other fantasy miniature wargames. Scale as chosen. Please see the size comparison picture for which scale is right for you. Please note that the models are supplied WITHOUT bases. The pictures show a digital render.Pictures may show additional models for size comparison. These addtional models are not part of this product.The 3D files are from Crab Miniatures. These 3D files are produced and sold under a commercial licence. Most of the miniatures are printed after you order them. The long processing time allows me to sensibly plan my working and printing time. Whenever possible, I try to cut the processing time short. The models are delivered unpainted and unassambled. This is a 3D printed product made of UV hardened resin. Models are cleaned and completely cured with UV light. Before printing, a support structure needs to be added to the models, these are normally removed after printing, but leave "scars" on the model. These are production-related and do not represent a defect in the product. Remains of the support structure might still be on the model and can be removed with a sharp hobby knife. Resin dust is a health hazard if inhaled into the lungs. Sanding and filing is not recommended. Otherwise, such work should only be carried out with appropriate protective equipment (fine dust mask) and/or wet sandpaper. It's possible that the models are hollow. In this case, the model has drainage holes through which the liquid resin could leak out. The inside of the model was then also cured. Drainage holes can be closed with modelling putty. Resin is heat-sensitive and can therefore deform during the printing process, the removal of the support structures, post-process curing, or shipping. Hot water or a heat gun/hair dryer can quickly remedy this. The affected part is heated and then carefully bent into the correct position. Important noticeWarning! Not for children under the age of 3. Choking hazard due to small parts.This product is not a toy.
€24.00*
Desert Skeleton Heavy Infantry (10 models)
Fantasy mass battle system compatible models, like e.g. Warhammer Fantasy, The Old World, Age of Sigmar, Kings of War, Oathmark, Dragon Rampant, or other fantasy miniature wargames. Scale as chosen. Please see the size comparison picture for which scale is right for you. A random selection of parts is made, but extra care is taken that it is balanced and duplicates are kept to a minimum.Selecting the Command Group replaces 3 normal models.The models are mostly one piece, but with a separate arm with the weapon. Please note that the models are supplied WITHOUT bases. The pictures show a digital render.The 3D files are from Crab Miniatures. These 3D files are produced and sold under a commercial licence. Most of the miniatures are printed after you order them. The long processing time allows me to sensibly plan my working and printing time. Whenever possible, I try to cut the processing time short. The models are delivered unpainted and unassambled. This is a 3D printed product made of UV hardened resin. Models are cleaned and completely cured with UV light. Before printing, a support structure needs to be added to the models, these are normally removed after printing, but leave "scars" on the model. These are production-related and do not represent a defect in the product. Remains of the support structure might still be on the model and can be removed with a sharp hobby knife. Resin dust is a health hazard if inhaled into the lungs. Sanding and filing is not recommended. Otherwise, such work should only be carried out with appropriate protective equipment (fine dust mask) and/or wet sandpaper. It's possible that the models are hollow. In this case, the model has drainage holes through which the liquid resin could leak out. The inside of the model was then also cured. Drainage holes can be closed with modelling putty. Resin is heat-sensitive and can therefore deform during the printing process, the removal of the support structures, post-process curing, or shipping. Hot water or a heat gun/hair dryer can quickly remedy this. The affected part is heated and then carefully bent into the correct position. Important noticeWarning! Not for children under the age of 3. Choking hazard due to small parts.This product is not a toy.
€25.00*
Desert Skeleton Heavy Infantry (Modular | 10 models)
Fantasy mass battle system compatible models, like e.g. Warhammer Fantasy, The Old World, Age of Sigmar, Kings of War, Oathmark, Dragon Rampant, or other fantasy miniature wargames. Scale as chosen. Please see the size comparison picture for which scale is right for you. A random selection of parts is made, but extra care is taken that it is balanced and duplicates are kept to a minimum.Selecting the Command Group replaces 3 normal models. Please note that the models are supplied WITHOUT bases. The pictures show a digital render.The 3D files are from Crab Miniatures. These 3D files are produced and sold under a commercial licence. Most of the miniatures are printed after you order them. The long processing time allows me to sensibly plan my working and printing time. Whenever possible, I try to cut the processing time short. The models are delivered unpainted and unassambled. This is a 3D printed product made of UV hardened resin. Models are cleaned and completely cured with UV light. Before printing, a support structure needs to be added to the models, these are normally removed after printing, but leave "scars" on the model. These are production-related and do not represent a defect in the product. Remains of the support structure might still be on the model and can be removed with a sharp hobby knife. Resin dust is a health hazard if inhaled into the lungs. Sanding and filing is not recommended. Otherwise, such work should only be carried out with appropriate protective equipment (fine dust mask) and/or wet sandpaper. It's possible that the models are hollow. In this case, the model has drainage holes through which the liquid resin could leak out. The inside of the model was then also cured. Drainage holes can be closed with modelling putty. Resin is heat-sensitive and can therefore deform during the printing process, the removal of the support structures, post-process curing, or shipping. Hot water or a heat gun/hair dryer can quickly remedy this. The affected part is heated and then carefully bent into the correct position. Important noticeWarning! Not for children under the age of 3. Choking hazard due to small parts.This product is not a toy.
€26.00*
Desert Skeleton Horses (6 models)
Fantasy mass battle system compatible models, like e.g. Warhammer Fantasy, The Old World, Age of Sigmar, Kings of War, Oathmark, Dragon Rampant, or other fantasy miniature wargames. Scale as chosen. Please see the size comparison picture for which scale is right for you. Six horses for conversions. Optionally with chariot poles. Please note that the models are supplied WITHOUT bases. The pictures show a digital render.The 3D files are from Crab Miniatures. These 3D files are produced and sold under a commercial licence. Most of the miniatures are printed after you order them. The long processing time allows me to sensibly plan my working and printing time. Whenever possible, I try to cut the processing time short. The models are delivered unpainted and unassambled. This is a 3D printed product made of UV hardened resin. Models are cleaned and completely cured with UV light. Before printing, a support structure needs to be added to the models, these are normally removed after printing, but leave "scars" on the model. These are production-related and do not represent a defect in the product. Remains of the support structure might still be on the model and can be removed with a sharp hobby knife. Resin dust is a health hazard if inhaled into the lungs. Sanding and filing is not recommended. Otherwise, such work should only be carried out with appropriate protective equipment (fine dust mask) and/or wet sandpaper. It's possible that the models are hollow. In this case, the model has drainage holes through which the liquid resin could leak out. The inside of the model was then also cured. Drainage holes can be closed with modelling putty. Resin is heat-sensitive and can therefore deform during the printing process, the removal of the support structures, post-process curing, or shipping. Hot water or a heat gun/hair dryer can quickly remedy this. The affected part is heated and then carefully bent into the correct position. Important noticeWarning! Not for children under the age of 3. Choking hazard due to small parts.This product is not a toy.
€18.00*
Desert Skeleton Snake Riders (3 models)
Fantasy mass battle system compatible models, like e.g. Warhammer Fantasy, The Old World, Age of Sigmar, Kings of War, Oathmark, Dragon Rampant, or other fantasy miniature wargames. Scale as chosen. Please see the size comparison picture for which scale is right for you. A random selection of parts is made.Selecting the Command Group replaces the normal models. Please note that the models are supplied WITHOUT bases. The pictures show a digital render.The 3D files are from Crab Miniatures. These 3D files are produced and sold under a commercial licence. Most of the miniatures are printed after you order them. The long processing time allows me to sensibly plan my working and printing time. Whenever possible, I try to cut the processing time short. The models are delivered unpainted and unassambled. This is a 3D printed product made of UV hardened resin. Models are cleaned and completely cured with UV light. Before printing, a support structure needs to be added to the models, these are normally removed after printing, but leave "scars" on the model. These are production-related and do not represent a defect in the product. Remains of the support structure might still be on the model and can be removed with a sharp hobby knife. Resin dust is a health hazard if inhaled into the lungs. Sanding and filing is not recommended. Otherwise, such work should only be carried out with appropriate protective equipment (fine dust mask) and/or wet sandpaper. It's possible that the models are hollow. In this case, the model has drainage holes through which the liquid resin could leak out. The inside of the model was then also cured. Drainage holes can be closed with modelling putty. Resin is heat-sensitive and can therefore deform during the printing process, the removal of the support structures, post-process curing, or shipping. Hot water or a heat gun/hair dryer can quickly remedy this. The affected part is heated and then carefully bent into the correct position. Important noticeWarning! Not for children under the age of 3. Choking hazard due to small parts.This product is not a toy.
€35.00*
Desert Skeleton Warriors (10 models)
Fantasy mass battle system compatible models, like e.g. Warhammer Fantasy, The Old World, Age of Sigmar, Kings of War, Oathmark, Dragon Rampant, or other fantasy miniature wargames. Scale as chosen. Please see the size comparison picture for which scale is right for you. A random selection of parts is made, but extra care is taken that it is balanced and duplicates are kept to a minimum.Selecting the Command Group replaces 3 normal models.The models are mostly one piece, but with a separate arm with the weapon. Please note that the models are supplied WITHOUT bases. The pictures show a digital render.The 3D files are from Crab Miniatures. These 3D files are produced and sold under a commercial licence. Most of the miniatures are printed after you order them. The long processing time allows me to sensibly plan my working and printing time. Whenever possible, I try to cut the processing time short. The models are delivered unpainted and unassambled. This is a 3D printed product made of UV hardened resin. Models are cleaned and completely cured with UV light. Before printing, a support structure needs to be added to the models, these are normally removed after printing, but leave "scars" on the model. These are production-related and do not represent a defect in the product. Remains of the support structure might still be on the model and can be removed with a sharp hobby knife. Resin dust is a health hazard if inhaled into the lungs. Sanding and filing is not recommended. Otherwise, such work should only be carried out with appropriate protective equipment (fine dust mask) and/or wet sandpaper. It's possible that the models are hollow. In this case, the model has drainage holes through which the liquid resin could leak out. The inside of the model was then also cured. Drainage holes can be closed with modelling putty. Resin is heat-sensitive and can therefore deform during the printing process, the removal of the support structures, post-process curing, or shipping. Hot water or a heat gun/hair dryer can quickly remedy this. The affected part is heated and then carefully bent into the correct position. Important noticeWarning! Not for children under the age of 3. Choking hazard due to small parts.This product is not a toy.
€20.00*
Desert Skeleton Warriors (20 models)
Fantasy mass battle system compatible models, like e.g. Warhammer Fantasy, The Old World, Age of Sigmar, Kings of War, Oathmark, Dragon Rampant, or other fantasy miniature wargames. Scale as chosen. Please see the size comparison picture for which scale is right for you. A random selection of parts is made, but extra care is taken that it is balanced and duplicates are kept to a minimum.Selecting the Command Group replaces 3 normal models.The models are mostly one piece, but with a separate arm with the weapon. Please note that the models are supplied WITHOUT bases. The pictures show a digital render.The 3D files are from Crab Miniatures. These 3D files are produced and sold under a commercial licence. Most of the miniatures are printed after you order them. The long processing time allows me to sensibly plan my working and printing time. Whenever possible, I try to cut the processing time short. The models are delivered unpainted and unassambled. This is a 3D printed product made of UV hardened resin. Models are cleaned and completely cured with UV light. Before printing, a support structure needs to be added to the models, these are normally removed after printing, but leave "scars" on the model. These are production-related and do not represent a defect in the product. Remains of the support structure might still be on the model and can be removed with a sharp hobby knife. Resin dust is a health hazard if inhaled into the lungs. Sanding and filing is not recommended. Otherwise, such work should only be carried out with appropriate protective equipment (fine dust mask) and/or wet sandpaper. It's possible that the models are hollow. In this case, the model has drainage holes through which the liquid resin could leak out. The inside of the model was then also cured. Drainage holes can be closed with modelling putty. Resin is heat-sensitive and can therefore deform during the printing process, the removal of the support structures, post-process curing, or shipping. Hot water or a heat gun/hair dryer can quickly remedy this. The affected part is heated and then carefully bent into the correct position. Important noticeWarning! Not for children under the age of 3. Choking hazard due to small parts.This product is not a toy.
€36.00*
Desert Skeleton Warriors (Modular | 10 models)
Fantasy mass battle system compatible models, like e.g. Warhammer Fantasy, The Old World, Age of Sigmar, Kings of War, Oathmark, Dragon Rampant, or other fantasy miniature wargames. Scale as chosen. Please see the size comparison picture for which scale is right for you. A random selection of parts is made, but extra care is taken that it is balanced and duplicates are kept to a minimum.Selecting the Command Group replaces 3 normal models. Please note that the models are supplied WITHOUT bases. The pictures show a digital render.The 3D files are from Crab Miniatures. These 3D files are produced and sold under a commercial licence. Most of the miniatures are printed after you order them. The long processing time allows me to sensibly plan my working and printing time. Whenever possible, I try to cut the processing time short. The models are delivered unpainted and unassambled. This is a 3D printed product made of UV hardened resin. Models are cleaned and completely cured with UV light. Before printing, a support structure needs to be added to the models, these are normally removed after printing, but leave "scars" on the model. These are production-related and do not represent a defect in the product. Remains of the support structure might still be on the model and can be removed with a sharp hobby knife. Resin dust is a health hazard if inhaled into the lungs. Sanding and filing is not recommended. Otherwise, such work should only be carried out with appropriate protective equipment (fine dust mask) and/or wet sandpaper. It's possible that the models are hollow. In this case, the model has drainage holes through which the liquid resin could leak out. The inside of the model was then also cured. Drainage holes can be closed with modelling putty. Resin is heat-sensitive and can therefore deform during the printing process, the removal of the support structures, post-process curing, or shipping. Hot water or a heat gun/hair dryer can quickly remedy this. The affected part is heated and then carefully bent into the correct position. Important noticeWarning! Not for children under the age of 3. Choking hazard due to small parts.This product is not a toy.
€25.00*
Desert Skeleton Warriors (Modular | 20 models)
Fantasy mass battle system compatible models, like e.g. Warhammer Fantasy, The Old World, Age of Sigmar, Kings of War, Oathmark, Dragon Rampant, or other fantasy miniature wargames. Scale as chosen. Please see the size comparison picture for which scale is right for you. A random selection of parts is made, but extra care is taken that it is balanced and duplicates are kept to a minimum.Selecting the Command Group replaces 3 normal models. Please note that the models are supplied WITHOUT bases. The pictures show a digital render.The 3D files are from Crab Miniatures. These 3D files are produced and sold under a commercial licence. Most of the miniatures are printed after you order them. The long processing time allows me to sensibly plan my working and printing time. Whenever possible, I try to cut the processing time short. The models are delivered unpainted and unassambled. This is a 3D printed product made of UV hardened resin. Models are cleaned and completely cured with UV light. Before printing, a support structure needs to be added to the models, these are normally removed after printing, but leave "scars" on the model. These are production-related and do not represent a defect in the product. Remains of the support structure might still be on the model and can be removed with a sharp hobby knife. Resin dust is a health hazard if inhaled into the lungs. Sanding and filing is not recommended. Otherwise, such work should only be carried out with appropriate protective equipment (fine dust mask) and/or wet sandpaper. It's possible that the models are hollow. In this case, the model has drainage holes through which the liquid resin could leak out. The inside of the model was then also cured. Drainage holes can be closed with modelling putty. Resin is heat-sensitive and can therefore deform during the printing process, the removal of the support structures, post-process curing, or shipping. Hot water or a heat gun/hair dryer can quickly remedy this. The affected part is heated and then carefully bent into the correct position. Important noticeWarning! Not for children under the age of 3. Choking hazard due to small parts.This product is not a toy.
€42.00*
Desert Swarms (3 bases)
Fantasy mass battle system compatible models, like e.g. Warhammer Fantasy, The Old World, Age of Sigmar, Kings of War, Oathmark, Dragon Rampant, or other fantasy miniature wargames. Scale as chosen. Please see the size comparison picture for which scale is right for you. Please note that the models are supplied WITHOUT bases. The pictures show a digital render.The 3D files are from Crab Miniatures. These 3D files are produced and sold under a commercial licence. Most of the miniatures are printed after you order them. The long processing time allows me to sensibly plan my working and printing time. Whenever possible, I try to cut the processing time short. The models are delivered unpainted and unassambled. This is a 3D printed product made of UV hardened resin. Models are cleaned and completely cured with UV light. Before printing, a support structure needs to be added to the models, these are normally removed after printing, but leave "scars" on the model. These are production-related and do not represent a defect in the product. Remains of the support structure might still be on the model and can be removed with a sharp hobby knife. Resin dust is a health hazard if inhaled into the lungs. Sanding and filing is not recommended. Otherwise, such work should only be carried out with appropriate protective equipment (fine dust mask) and/or wet sandpaper. It's possible that the models are hollow. In this case, the model has drainage holes through which the liquid resin could leak out. The inside of the model was then also cured. Drainage holes can be closed with modelling putty. Resin is heat-sensitive and can therefore deform during the printing process, the removal of the support structures, post-process curing, or shipping. Hot water or a heat gun/hair dryer can quickly remedy this. The affected part is heated and then carefully bent into the correct position. Important noticeWarning! Not for children under the age of 3. Choking hazard due to small parts.This product is not a toy.
€9.00*
Giant Desert Skeleton
Fantasy mass battle system compatible models, like e.g. Warhammer Fantasy, The Old World, Age of Sigmar, Kings of War, Oathmark, Dragon Rampant, or other fantasy miniature wargames. Scale as chosen. Please see the size comparison picture for which scale is right for you.You get a random head and the weapons of choice. Please note that the models are supplied WITHOUT bases. The pictures show a digital render.Pictures may show additional models for size comparison. These addtional models are not part of this product.The 3D files are from Crab Miniatures. These 3D files are produced and sold under a commercial licence. Most of the miniatures are printed after you order them. The long processing time allows me to sensibly plan my working and printing time. Whenever possible, I try to cut the processing time short. The models are delivered unpainted and unassambled. This is a 3D printed product made of UV hardened resin. Models are cleaned and completely cured with UV light. Before printing, a support structure needs to be added to the models, these are normally removed after printing, but leave "scars" on the model. These are production-related and do not represent a defect in the product. Remains of the support structure might still be on the model and can be removed with a sharp hobby knife. Resin dust is a health hazard if inhaled into the lungs. Sanding and filing is not recommended. Otherwise, such work should only be carried out with appropriate protective equipment (fine dust mask) and/or wet sandpaper. It's possible that the models are hollow. In this case, the model has drainage holes through which the liquid resin could leak out. The inside of the model was then also cured. Drainage holes can be closed with modelling putty. Resin is heat-sensitive and can therefore deform during the printing process, the removal of the support structures, post-process curing, or shipping. Hot water or a heat gun/hair dryer can quickly remedy this. The affected part is heated and then carefully bent into the correct position. Important noticeWarning! Not for children under the age of 3. Choking hazard due to small parts.This product is not a toy.
€25.00*
Giant Undead Scorpion
Fantasy mass battle system compatible models, like e.g. Warhammer Fantasy, The Old World, Age of Sigmar, Kings of War, Oathmark, Dragon Rampant, or other fantasy miniature wargames. Scale as chosen. Please see the size comparison picture for which scale is right for you.A random selection of parts is made. Comes with a normal stinger and a stinger with skull. Please note that the models are supplied WITHOUT bases. The pictures show a digital render.Pictures may show additional models for size comparison. These addtional models are not part of this product.The 3D files are from Crab Miniatures. These 3D files are produced and sold under a commercial licence. Most of the miniatures are printed after you order them. The long processing time allows me to sensibly plan my working and printing time. Whenever possible, I try to cut the processing time short. The models are delivered unpainted and unassambled. This is a 3D printed product made of UV hardened resin. Models are cleaned and completely cured with UV light. Before printing, a support structure needs to be added to the models, these are normally removed after printing, but leave "scars" on the model. These are production-related and do not represent a defect in the product. Remains of the support structure might still be on the model and can be removed with a sharp hobby knife. Resin dust is a health hazard if inhaled into the lungs. Sanding and filing is not recommended. Otherwise, such work should only be carried out with appropriate protective equipment (fine dust mask) and/or wet sandpaper. It's possible that the models are hollow. In this case, the model has drainage holes through which the liquid resin could leak out. The inside of the model was then also cured. Drainage holes can be closed with modelling putty. Resin is heat-sensitive and can therefore deform during the printing process, the removal of the support structures, post-process curing, or shipping. Hot water or a heat gun/hair dryer can quickly remedy this. The affected part is heated and then carefully bent into the correct position. Important noticeWarning! Not for children under the age of 3. Choking hazard due to small parts.This product is not a toy.
€18.00*
Hierophant
Fantasy mass battle system compatible models, like e.g. Warhammer Fantasy, The Old World, Age of Sigmar, Kings of War, Oathmark, Dragon Rampant, or other fantasy miniature wargames. Scale as chosen. Please see the size comparison picture for which scale is right for you. Both head options are included. Please note that the models are supplied WITHOUT bases. The pictures show a digital render.The 3D files are from Crab Miniatures. These 3D files are produced and sold under a commercial licence. Most of the miniatures are printed after you order them. The long processing time allows me to sensibly plan my working and printing time. Whenever possible, I try to cut the processing time short. The models are delivered unpainted and unassambled. This is a 3D printed product made of UV hardened resin. Models are cleaned and completely cured with UV light. Before printing, a support structure needs to be added to the models, these are normally removed after printing, but leave "scars" on the model. These are production-related and do not represent a defect in the product. Remains of the support structure might still be on the model and can be removed with a sharp hobby knife. Resin dust is a health hazard if inhaled into the lungs. Sanding and filing is not recommended. Otherwise, such work should only be carried out with appropriate protective equipment (fine dust mask) and/or wet sandpaper. It's possible that the models are hollow. In this case, the model has drainage holes through which the liquid resin could leak out. The inside of the model was then also cured. Drainage holes can be closed with modelling putty. Resin is heat-sensitive and can therefore deform during the printing process, the removal of the support structures, post-process curing, or shipping. Hot water or a heat gun/hair dryer can quickly remedy this. The affected part is heated and then carefully bent into the correct position. Important noticeWarning! Not for children under the age of 3. Choking hazard due to small parts.This product is not a toy.
€7.00*