Filter
–
Ark of the Covenant (2 models)
28 mm scale for collectors, painters and gamers, e.g. for Hail Caesar, Field of Glory, Triumph, Mortem et Gloriam, Impetus!, or other historical miniature wargames. Incldues the Ark with bearers and a second separate Ark that can be used as an objective or something similar. Please note that the models are supplied WITHOUT bases. The pictures show a digital render. Printed and painted models by Red Copper Miniatures. The 3D files are from Red Copper Miniatures. These 3D files are produced and sold under a commercial licence. Most of the miniatures are printed after you order them. The long processing time allows me to sensibly plan my working and printing time. Whenever possible, I try to cut the processing time short. The models are delivered unpainted and unassambled. This is a 3D printed product made of UV hardened resin. Models are cleaned and completely cured with UV light. Before printing, a support structure needs to be added to the models, these are normally removed after printing, but leave "scars" on the model. These are production-related and do not represent a defect in the product. Remains of the support structure might still be on the model and can be removed with a sharp hobby knife. Resin dust is a health hazard if inhaled into the lungs. Sanding and filing is not recommended. Otherwise, such work should only be carried out with appropriate protective equipment (fine dust mask) and/or wet sandpaper. It's possible that the models are hollow. In this case, the model has drainage holes through which the liquid resin could leak out. The inside of the model was then also cured. Drainage holes can be closed with modelling putty. Resin is heat-sensitive and can therefore deform during the printing process, the removal of the support structures, post-process curing, or shipping. Hot water or a heat gun/hair dryer can quickly remedy this. The affected part is heated and then carefully bent into the correct position. Important noticeWarning! Not for children under the age of 3. Choking hazard due to small parts.This product is not a toy.
From €7.00*
Civilians of the Ancient Middle East (5 Modelle)
28 mm scale for collectors, painters and gamers, e.g. for Hail Caesar, Field of Glory, Triumph, Mortem et Gloriam, Impetus!, or other historical miniature wargames.Please note that the models are supplied WITHOUT bases. The pictures show a digital render. Printed and painted models by Red Copper Miniatures. The 3D files are from Red Copper Miniatures. These 3D files are produced and sold under a commercial licence. Most of the miniatures are printed after you order them. The long processing time allows me to sensibly plan my working and printing time. Whenever possible, I try to cut the processing time short. The models are delivered unpainted and unassambled. This is a 3D printed product made of UV hardened resin. Models are cleaned and completely cured with UV light. Before printing, a support structure needs to be added to the models, these are normally removed after printing, but leave "scars" on the model. These are production-related and do not represent a defect in the product. Remains of the support structure might still be on the model and can be removed with a sharp hobby knife. Resin dust is a health hazard if inhaled into the lungs. Sanding and filing is not recommended. Otherwise, such work should only be carried out with appropriate protective equipment (fine dust mask) and/or wet sandpaper. It's possible that the models are hollow. In this case, the model has drainage holes through which the liquid resin could leak out. The inside of the model was then also cured. Drainage holes can be closed with modelling putty. Resin is heat-sensitive and can therefore deform during the printing process, the removal of the support structures, post-process curing, or shipping. Hot water or a heat gun/hair dryer can quickly remedy this. The affected part is heated and then carefully bent into the correct position. Important noticeWarning! Not for children under the age of 3. Choking hazard due to small parts.This product is not a toy.
From €6.00*
David
28 mm scale for collectors, painters and gamers, e.g. for Hail Caesar, Field of Glory, Triumph, Mortem et Gloriam, Impetus!, or other historical miniature wargames.Please note that the models are supplied WITHOUT bases. The pictures show a digital render. Printed and painted models by Red Copper Miniatures. The 3D files are from Red Copper Miniatures. These 3D files are produced and sold under a commercial licence. Most of the miniatures are printed after you order them. The long processing time allows me to sensibly plan my working and printing time. Whenever possible, I try to cut the processing time short. The models are delivered unpainted and unassambled. This is a 3D printed product made of UV hardened resin. Models are cleaned and completely cured with UV light. Before printing, a support structure needs to be added to the models, these are normally removed after printing, but leave "scars" on the model. These are production-related and do not represent a defect in the product. Remains of the support structure might still be on the model and can be removed with a sharp hobby knife. Resin dust is a health hazard if inhaled into the lungs. Sanding and filing is not recommended. Otherwise, such work should only be carried out with appropriate protective equipment (fine dust mask) and/or wet sandpaper. It's possible that the models are hollow. In this case, the model has drainage holes through which the liquid resin could leak out. The inside of the model was then also cured. Drainage holes can be closed with modelling putty. Resin is heat-sensitive and can therefore deform during the printing process, the removal of the support structures, post-process curing, or shipping. Hot water or a heat gun/hair dryer can quickly remedy this. The affected part is heated and then carefully bent into the correct position. Important noticeWarning! Not for children under the age of 3. Choking hazard due to small parts.This product is not a toy.
€4.00*
David vs Goliath (Diorama)
28 mm scale for collectors, painters and gamers, e.g. for Hail Caesar, Field of Glory, Triumph, Mortem et Gloriam, Impetus!, or other historical miniature wargames.Please note that the models are supplied WITHOUT bases. The pictures show a digital render. Printed and painted models by Red Copper Miniatures. The 3D files are from Red Copper Miniatures. These 3D files are produced and sold under a commercial licence. Most of the miniatures are printed after you order them. The long processing time allows me to sensibly plan my working and printing time. Whenever possible, I try to cut the processing time short. The models are delivered unpainted and unassambled. This is a 3D printed product made of UV hardened resin. Models are cleaned and completely cured with UV light. Before printing, a support structure needs to be added to the models, these are normally removed after printing, but leave "scars" on the model. These are production-related and do not represent a defect in the product. Remains of the support structure might still be on the model and can be removed with a sharp hobby knife. Resin dust is a health hazard if inhaled into the lungs. Sanding and filing is not recommended. Otherwise, such work should only be carried out with appropriate protective equipment (fine dust mask) and/or wet sandpaper. It's possible that the models are hollow. In this case, the model has drainage holes through which the liquid resin could leak out. The inside of the model was then also cured. Drainage holes can be closed with modelling putty. Resin is heat-sensitive and can therefore deform during the printing process, the removal of the support structures, post-process curing, or shipping. Hot water or a heat gun/hair dryer can quickly remedy this. The affected part is heated and then carefully bent into the correct position. Important noticeWarning! Not for children under the age of 3. Choking hazard due to small parts.This product is not a toy.
From €5.00*
Egyptian Bowmen (5 models)
28 mm scale for collectors, painters and gamers, e.g. for Hail Caesar, Field of Glory, Triumph, Mortem et Gloriam, Impetus!, or other historical miniature wargames.Please note that the models are supplied WITHOUT bases. The pictures show a digital render. Printed and painted models by Red Copper Miniatures. The 3D files are from Red Copper Miniatures. These 3D files are produced and sold under a commercial licence. Most of the miniatures are printed after you order them. The long processing time allows me to sensibly plan my working and printing time. Whenever possible, I try to cut the processing time short. The models are delivered unpainted and unassambled. This is a 3D printed product made of UV hardened resin. Models are cleaned and completely cured with UV light. Before printing, a support structure needs to be added to the models, these are normally removed after printing, but leave "scars" on the model. These are production-related and do not represent a defect in the product. Remains of the support structure might still be on the model and can be removed with a sharp hobby knife. Resin dust is a health hazard if inhaled into the lungs. Sanding and filing is not recommended. Otherwise, such work should only be carried out with appropriate protective equipment (fine dust mask) and/or wet sandpaper. It's possible that the models are hollow. In this case, the model has drainage holes through which the liquid resin could leak out. The inside of the model was then also cured. Drainage holes can be closed with modelling putty. Resin is heat-sensitive and can therefore deform during the printing process, the removal of the support structures, post-process curing, or shipping. Hot water or a heat gun/hair dryer can quickly remedy this. The affected part is heated and then carefully bent into the correct position. Important noticeWarning! Not for children under the age of 3. Choking hazard due to small parts.This product is not a toy.
From €6.00*
Egyptian Command Group (3 models)
28 mm scale for collectors, painters and gamers, e.g. for Hail Caesar, Field of Glory, Triumph, Mortem et Gloriam, Impetus!, or other historical miniature wargames.Please note that the models are supplied WITHOUT bases. The pictures show a digital render. Printed and painted models by Red Copper Miniatures. The 3D files are from Red Copper Miniatures. These 3D files are produced and sold under a commercial licence. Most of the miniatures are printed after you order them. The long processing time allows me to sensibly plan my working and printing time. Whenever possible, I try to cut the processing time short. The models are delivered unpainted and unassambled. This is a 3D printed product made of UV hardened resin. Models are cleaned and completely cured with UV light. Before printing, a support structure needs to be added to the models, these are normally removed after printing, but leave "scars" on the model. These are production-related and do not represent a defect in the product. Remains of the support structure might still be on the model and can be removed with a sharp hobby knife. Resin dust is a health hazard if inhaled into the lungs. Sanding and filing is not recommended. Otherwise, such work should only be carried out with appropriate protective equipment (fine dust mask) and/or wet sandpaper. It's possible that the models are hollow. In this case, the model has drainage holes through which the liquid resin could leak out. The inside of the model was then also cured. Drainage holes can be closed with modelling putty. Resin is heat-sensitive and can therefore deform during the printing process, the removal of the support structures, post-process curing, or shipping. Hot water or a heat gun/hair dryer can quickly remedy this. The affected part is heated and then carefully bent into the correct position. Important noticeWarning! Not for children under the age of 3. Choking hazard due to small parts.This product is not a toy.
From €4.00*
Egyptian Light Chariots (3 models)
28 mm scale for collectors, painters and gamers, e.g. for Hail Caesar, Field of Glory, Triumph, Mortem et Gloriam, Impetus!, or other historical miniature wargames.Please note that the models are supplied WITHOUT bases. The pictures show a digital render. Printed and painted models by Red Copper Miniatures. The 3D files are from Red Copper Miniatures. These 3D files are produced and sold under a commercial licence. Most of the miniatures are printed after you order them. The long processing time allows me to sensibly plan my working and printing time. Whenever possible, I try to cut the processing time short. The models are delivered unpainted and unassambled. This is a 3D printed product made of UV hardened resin. Models are cleaned and completely cured with UV light. Before printing, a support structure needs to be added to the models, these are normally removed after printing, but leave "scars" on the model. These are production-related and do not represent a defect in the product. Remains of the support structure might still be on the model and can be removed with a sharp hobby knife. Resin dust is a health hazard if inhaled into the lungs. Sanding and filing is not recommended. Otherwise, such work should only be carried out with appropriate protective equipment (fine dust mask) and/or wet sandpaper. It's possible that the models are hollow. In this case, the model has drainage holes through which the liquid resin could leak out. The inside of the model was then also cured. Drainage holes can be closed with modelling putty. Resin is heat-sensitive and can therefore deform during the printing process, the removal of the support structures, post-process curing, or shipping. Hot water or a heat gun/hair dryer can quickly remedy this. The affected part is heated and then carefully bent into the correct position. Important noticeWarning! Not for children under the age of 3. Choking hazard due to small parts.This product is not a toy.
From €18.00*
Egyptian Royal Guard (5 models)
28 mm scale for collectors, painters and gamers, e.g. for Hail Caesar, Field of Glory, Triumph, Mortem et Gloriam, Impetus!, or other historical miniature wargames.Please note that the models are supplied WITHOUT bases. The pictures show a digital render. Printed and painted models by Red Copper Miniatures. The 3D files are from Red Copper Miniatures. These 3D files are produced and sold under a commercial licence. Most of the miniatures are printed after you order them. The long processing time allows me to sensibly plan my working and printing time. Whenever possible, I try to cut the processing time short. The models are delivered unpainted and unassambled. This is a 3D printed product made of UV hardened resin. Models are cleaned and completely cured with UV light. Before printing, a support structure needs to be added to the models, these are normally removed after printing, but leave "scars" on the model. These are production-related and do not represent a defect in the product. Remains of the support structure might still be on the model and can be removed with a sharp hobby knife. Resin dust is a health hazard if inhaled into the lungs. Sanding and filing is not recommended. Otherwise, such work should only be carried out with appropriate protective equipment (fine dust mask) and/or wet sandpaper. It's possible that the models are hollow. In this case, the model has drainage holes through which the liquid resin could leak out. The inside of the model was then also cured. Drainage holes can be closed with modelling putty. Resin is heat-sensitive and can therefore deform during the printing process, the removal of the support structures, post-process curing, or shipping. Hot water or a heat gun/hair dryer can quickly remedy this. The affected part is heated and then carefully bent into the correct position. Important noticeWarning! Not for children under the age of 3. Choking hazard due to small parts.This product is not a toy.
From €6.00*
Egyptian Warriors (5 models)
28 mm scale for collectors, painters and gamers, e.g. for Hail Caesar, Field of Glory, Triumph, Mortem et Gloriam, Impetus!, or other historical miniature wargames.Please note that the models are supplied WITHOUT bases. The pictures show a digital render. Printed and painted models by Red Copper Miniatures. The 3D files are from Red Copper Miniatures. These 3D files are produced and sold under a commercial licence. Most of the miniatures are printed after you order them. The long processing time allows me to sensibly plan my working and printing time. Whenever possible, I try to cut the processing time short. The models are delivered unpainted and unassambled. This is a 3D printed product made of UV hardened resin. Models are cleaned and completely cured with UV light. Before printing, a support structure needs to be added to the models, these are normally removed after printing, but leave "scars" on the model. These are production-related and do not represent a defect in the product. Remains of the support structure might still be on the model and can be removed with a sharp hobby knife. Resin dust is a health hazard if inhaled into the lungs. Sanding and filing is not recommended. Otherwise, such work should only be carried out with appropriate protective equipment (fine dust mask) and/or wet sandpaper. It's possible that the models are hollow. In this case, the model has drainage holes through which the liquid resin could leak out. The inside of the model was then also cured. Drainage holes can be closed with modelling putty. Resin is heat-sensitive and can therefore deform during the printing process, the removal of the support structures, post-process curing, or shipping. Hot water or a heat gun/hair dryer can quickly remedy this. The affected part is heated and then carefully bent into the correct position. Important noticeWarning! Not for children under the age of 3. Choking hazard due to small parts.This product is not a toy.
From €6.00*
Goliath
28 mm scale for collectors, painters and gamers, e.g. for Hail Caesar, Field of Glory, Triumph, Mortem et Gloriam, Impetus!, or other historical miniature wargames.Please note that the models are supplied WITHOUT bases. The pictures show a digital render. Printed and painted models by Red Copper Miniatures. The 3D files are from Red Copper Miniatures. These 3D files are produced and sold under a commercial licence. Most of the miniatures are printed after you order them. The long processing time allows me to sensibly plan my working and printing time. Whenever possible, I try to cut the processing time short. The models are delivered unpainted and unassambled. This is a 3D printed product made of UV hardened resin. Models are cleaned and completely cured with UV light. Before printing, a support structure needs to be added to the models, these are normally removed after printing, but leave "scars" on the model. These are production-related and do not represent a defect in the product. Remains of the support structure might still be on the model and can be removed with a sharp hobby knife. Resin dust is a health hazard if inhaled into the lungs. Sanding and filing is not recommended. Otherwise, such work should only be carried out with appropriate protective equipment (fine dust mask) and/or wet sandpaper. It's possible that the models are hollow. In this case, the model has drainage holes through which the liquid resin could leak out. The inside of the model was then also cured. Drainage holes can be closed with modelling putty. Resin is heat-sensitive and can therefore deform during the printing process, the removal of the support structures, post-process curing, or shipping. Hot water or a heat gun/hair dryer can quickly remedy this. The affected part is heated and then carefully bent into the correct position. Important noticeWarning! Not for children under the age of 3. Choking hazard due to small parts.This product is not a toy.
From €4.00*
Hebrew Heroes (5 models)
28 mm scale for collectors, painters and gamers, e.g. for Hail Caesar, Field of Glory, Triumph, Mortem et Gloriam, Impetus!, or other historical miniature wargames.Please note that the models are supplied WITHOUT bases. The pictures show a digital render. Printed and painted models by Red Copper Miniatures. The 3D files are from Red Copper Miniatures. These 3D files are produced and sold under a commercial licence. Most of the miniatures are printed after you order them. The long processing time allows me to sensibly plan my working and printing time. Whenever possible, I try to cut the processing time short. The models are delivered unpainted and unassambled. This is a 3D printed product made of UV hardened resin. Models are cleaned and completely cured with UV light. Before printing, a support structure needs to be added to the models, these are normally removed after printing, but leave "scars" on the model. These are production-related and do not represent a defect in the product. Remains of the support structure might still be on the model and can be removed with a sharp hobby knife. Resin dust is a health hazard if inhaled into the lungs. Sanding and filing is not recommended. Otherwise, such work should only be carried out with appropriate protective equipment (fine dust mask) and/or wet sandpaper. It's possible that the models are hollow. In this case, the model has drainage holes through which the liquid resin could leak out. The inside of the model was then also cured. Drainage holes can be closed with modelling putty. Resin is heat-sensitive and can therefore deform during the printing process, the removal of the support structures, post-process curing, or shipping. Hot water or a heat gun/hair dryer can quickly remedy this. The affected part is heated and then carefully bent into the correct position. Important noticeWarning! Not for children under the age of 3. Choking hazard due to small parts.This product is not a toy.
From €6.00*
Hebrew Skirmishers (5 models)
28 mm scale for collectors, painters and gamers, e.g. for Hail Caesar, Field of Glory, Triumph, Mortem et Gloriam, Impetus!, or other historical miniature wargames.Please note that the models are supplied WITHOUT bases. The pictures show a digital render. Printed and painted models by Red Copper Miniatures. The 3D files are from Red Copper Miniatures. These 3D files are produced and sold under a commercial licence. Most of the miniatures are printed after you order them. The long processing time allows me to sensibly plan my working and printing time. Whenever possible, I try to cut the processing time short. The models are delivered unpainted and unassambled. This is a 3D printed product made of UV hardened resin. Models are cleaned and completely cured with UV light. Before printing, a support structure needs to be added to the models, these are normally removed after printing, but leave "scars" on the model. These are production-related and do not represent a defect in the product. Remains of the support structure might still be on the model and can be removed with a sharp hobby knife. Resin dust is a health hazard if inhaled into the lungs. Sanding and filing is not recommended. Otherwise, such work should only be carried out with appropriate protective equipment (fine dust mask) and/or wet sandpaper. It's possible that the models are hollow. In this case, the model has drainage holes through which the liquid resin could leak out. The inside of the model was then also cured. Drainage holes can be closed with modelling putty. Resin is heat-sensitive and can therefore deform during the printing process, the removal of the support structures, post-process curing, or shipping. Hot water or a heat gun/hair dryer can quickly remedy this. The affected part is heated and then carefully bent into the correct position. Important noticeWarning! Not for children under the age of 3. Choking hazard due to small parts.This product is not a toy.
From €6.00*
Hebrew Spearmen (5 models)
28 mm scale for collectors, painters and gamers, e.g. for Hail Caesar, Field of Glory, Triumph, Mortem et Gloriam, Impetus!, or other historical miniature wargames.Please note that the models are supplied WITHOUT bases. The pictures show a digital render. Printed and painted models by Red Copper Miniatures. The 3D files are from Red Copper Miniatures. These 3D files are produced and sold under a commercial licence. Most of the miniatures are printed after you order them. The long processing time allows me to sensibly plan my working and printing time. Whenever possible, I try to cut the processing time short. The models are delivered unpainted and unassambled. This is a 3D printed product made of UV hardened resin. Models are cleaned and completely cured with UV light. Before printing, a support structure needs to be added to the models, these are normally removed after printing, but leave "scars" on the model. These are production-related and do not represent a defect in the product. Remains of the support structure might still be on the model and can be removed with a sharp hobby knife. Resin dust is a health hazard if inhaled into the lungs. Sanding and filing is not recommended. Otherwise, such work should only be carried out with appropriate protective equipment (fine dust mask) and/or wet sandpaper. It's possible that the models are hollow. In this case, the model has drainage holes through which the liquid resin could leak out. The inside of the model was then also cured. Drainage holes can be closed with modelling putty. Resin is heat-sensitive and can therefore deform during the printing process, the removal of the support structures, post-process curing, or shipping. Hot water or a heat gun/hair dryer can quickly remedy this. The affected part is heated and then carefully bent into the correct position. Important noticeWarning! Not for children under the age of 3. Choking hazard due to small parts.This product is not a toy.
From €6.00*
Hebrew Warband (5 models)
28 mm scale for collectors, painters and gamers, e.g. for Hail Caesar, Field of Glory, Triumph, Mortem et Gloriam, Impetus!, or other historical miniature wargames.Please note that the models are supplied WITHOUT bases. The pictures show a digital render. Printed and painted models by Red Copper Miniatures. The 3D files are from Red Copper Miniatures. These 3D files are produced and sold under a commercial licence. Most of the miniatures are printed after you order them. The long processing time allows me to sensibly plan my working and printing time. Whenever possible, I try to cut the processing time short. The models are delivered unpainted and unassambled. This is a 3D printed product made of UV hardened resin. Models are cleaned and completely cured with UV light. Before printing, a support structure needs to be added to the models, these are normally removed after printing, but leave "scars" on the model. These are production-related and do not represent a defect in the product. Remains of the support structure might still be on the model and can be removed with a sharp hobby knife. Resin dust is a health hazard if inhaled into the lungs. Sanding and filing is not recommended. Otherwise, such work should only be carried out with appropriate protective equipment (fine dust mask) and/or wet sandpaper. It's possible that the models are hollow. In this case, the model has drainage holes through which the liquid resin could leak out. The inside of the model was then also cured. Drainage holes can be closed with modelling putty. Resin is heat-sensitive and can therefore deform during the printing process, the removal of the support structures, post-process curing, or shipping. Hot water or a heat gun/hair dryer can quickly remedy this. The affected part is heated and then carefully bent into the correct position. Important noticeWarning! Not for children under the age of 3. Choking hazard due to small parts.This product is not a toy.
From €6.00*
Hittite Command Group (3 models)
28 mm scale for collectors, painters and gamers, e.g. for Hail Caesar, Field of Glory, Triumph, Mortem et Gloriam, Impetus!, or other historical miniature wargames.Please note that the models are supplied WITHOUT bases. The pictures show a digital render. Printed and painted models by Red Copper Miniatures. The 3D files are from Red Copper Miniatures. These 3D files are produced and sold under a commercial licence. Most of the miniatures are printed after you order them. The long processing time allows me to sensibly plan my working and printing time. Whenever possible, I try to cut the processing time short. The models are delivered unpainted and unassambled. This is a 3D printed product made of UV hardened resin. Models are cleaned and completely cured with UV light. Before printing, a support structure needs to be added to the models, these are normally removed after printing, but leave "scars" on the model. These are production-related and do not represent a defect in the product. Remains of the support structure might still be on the model and can be removed with a sharp hobby knife. Resin dust is a health hazard if inhaled into the lungs. Sanding and filing is not recommended. Otherwise, such work should only be carried out with appropriate protective equipment (fine dust mask) and/or wet sandpaper. It's possible that the models are hollow. In this case, the model has drainage holes through which the liquid resin could leak out. The inside of the model was then also cured. Drainage holes can be closed with modelling putty. Resin is heat-sensitive and can therefore deform during the printing process, the removal of the support structures, post-process curing, or shipping. Hot water or a heat gun/hair dryer can quickly remedy this. The affected part is heated and then carefully bent into the correct position. Important noticeWarning! Not for children under the age of 3. Choking hazard due to small parts.This product is not a toy.
From €4.00*
Hittite Heavy Chariots (3 models)
28 mm scale for collectors, painters and gamers, e.g. for Hail Caesar, Field of Glory, Triumph, Mortem et Gloriam, Impetus!, or other historical miniature wargames.Please note that the models are supplied WITHOUT bases. The pictures show a digital render. Printed and painted models by Red Copper Miniatures. The 3D files are from Red Copper Miniatures. These 3D files are produced and sold under a commercial licence. Most of the miniatures are printed after you order them. The long processing time allows me to sensibly plan my working and printing time. Whenever possible, I try to cut the processing time short. The models are delivered unpainted and unassambled. This is a 3D printed product made of UV hardened resin. Models are cleaned and completely cured with UV light. Before printing, a support structure needs to be added to the models, these are normally removed after printing, but leave "scars" on the model. These are production-related and do not represent a defect in the product. Remains of the support structure might still be on the model and can be removed with a sharp hobby knife. Resin dust is a health hazard if inhaled into the lungs. Sanding and filing is not recommended. Otherwise, such work should only be carried out with appropriate protective equipment (fine dust mask) and/or wet sandpaper. It's possible that the models are hollow. In this case, the model has drainage holes through which the liquid resin could leak out. The inside of the model was then also cured. Drainage holes can be closed with modelling putty. Resin is heat-sensitive and can therefore deform during the printing process, the removal of the support structures, post-process curing, or shipping. Hot water or a heat gun/hair dryer can quickly remedy this. The affected part is heated and then carefully bent into the correct position. Important noticeWarning! Not for children under the age of 3. Choking hazard due to small parts.This product is not a toy.
From €18.50*
Hittite Horde (5 models)
28 mm scale for collectors, painters and gamers, e.g. for Hail Caesar, Field of Glory, Triumph, Mortem et Gloriam, Impetus!, or other historical miniature wargames.Please note that the models are supplied WITHOUT bases. The pictures show a digital render. Printed and painted models by Red Copper Miniatures. The 3D files are from Red Copper Miniatures. These 3D files are produced and sold under a commercial licence. Most of the miniatures are printed after you order them. The long processing time allows me to sensibly plan my working and printing time. Whenever possible, I try to cut the processing time short. The models are delivered unpainted and unassambled. This is a 3D printed product made of UV hardened resin. Models are cleaned and completely cured with UV light. Before printing, a support structure needs to be added to the models, these are normally removed after printing, but leave "scars" on the model. These are production-related and do not represent a defect in the product. Remains of the support structure might still be on the model and can be removed with a sharp hobby knife. Resin dust is a health hazard if inhaled into the lungs. Sanding and filing is not recommended. Otherwise, such work should only be carried out with appropriate protective equipment (fine dust mask) and/or wet sandpaper. It's possible that the models are hollow. In this case, the model has drainage holes through which the liquid resin could leak out. The inside of the model was then also cured. Drainage holes can be closed with modelling putty. Resin is heat-sensitive and can therefore deform during the printing process, the removal of the support structures, post-process curing, or shipping. Hot water or a heat gun/hair dryer can quickly remedy this. The affected part is heated and then carefully bent into the correct position. Important noticeWarning! Not for children under the age of 3. Choking hazard due to small parts.This product is not a toy.
From €6.00*
Hittite Royal Guard (5 models)
28 mm scale for collectors, painters and gamers, e.g. for Hail Caesar, Field of Glory, Triumph, Mortem et Gloriam, Impetus!, or other historical miniature wargames.Please note that the models are supplied WITHOUT bases. The pictures show a digital render. Printed and painted models by Red Copper Miniatures. The 3D files are from Red Copper Miniatures. These 3D files are produced and sold under a commercial licence. Most of the miniatures are printed after you order them. The long processing time allows me to sensibly plan my working and printing time. Whenever possible, I try to cut the processing time short. The models are delivered unpainted and unassambled. This is a 3D printed product made of UV hardened resin. Models are cleaned and completely cured with UV light. Before printing, a support structure needs to be added to the models, these are normally removed after printing, but leave "scars" on the model. These are production-related and do not represent a defect in the product. Remains of the support structure might still be on the model and can be removed with a sharp hobby knife. Resin dust is a health hazard if inhaled into the lungs. Sanding and filing is not recommended. Otherwise, such work should only be carried out with appropriate protective equipment (fine dust mask) and/or wet sandpaper. It's possible that the models are hollow. In this case, the model has drainage holes through which the liquid resin could leak out. The inside of the model was then also cured. Drainage holes can be closed with modelling putty. Resin is heat-sensitive and can therefore deform during the printing process, the removal of the support structures, post-process curing, or shipping. Hot water or a heat gun/hair dryer can quickly remedy this. The affected part is heated and then carefully bent into the correct position. Important noticeWarning! Not for children under the age of 3. Choking hazard due to small parts.This product is not a toy.
From €6.00*
Hittite Skirmishers (5 models)
28 mm scale for collectors, painters and gamers, e.g. for Hail Caesar, Field of Glory, Triumph, Mortem et Gloriam, Impetus!, or other historical miniature wargames.Please note that the models are supplied WITHOUT bases. The pictures show a digital render. Printed and painted models by Red Copper Miniatures. The 3D files are from Red Copper Miniatures. These 3D files are produced and sold under a commercial licence. Most of the miniatures are printed after you order them. The long processing time allows me to sensibly plan my working and printing time. Whenever possible, I try to cut the processing time short. The models are delivered unpainted and unassambled. This is a 3D printed product made of UV hardened resin. Models are cleaned and completely cured with UV light. Before printing, a support structure needs to be added to the models, these are normally removed after printing, but leave "scars" on the model. These are production-related and do not represent a defect in the product. Remains of the support structure might still be on the model and can be removed with a sharp hobby knife. Resin dust is a health hazard if inhaled into the lungs. Sanding and filing is not recommended. Otherwise, such work should only be carried out with appropriate protective equipment (fine dust mask) and/or wet sandpaper. It's possible that the models are hollow. In this case, the model has drainage holes through which the liquid resin could leak out. The inside of the model was then also cured. Drainage holes can be closed with modelling putty. Resin is heat-sensitive and can therefore deform during the printing process, the removal of the support structures, post-process curing, or shipping. Hot water or a heat gun/hair dryer can quickly remedy this. The affected part is heated and then carefully bent into the correct position. Important noticeWarning! Not for children under the age of 3. Choking hazard due to small parts.This product is not a toy.
From €6.00*
Hittite Spearmen (5 models)
28 mm scale for collectors, painters and gamers, e.g. for Hail Caesar, Field of Glory, Triumph, Mortem et Gloriam, Impetus!, or other historical miniature wargames.Please note that the models are supplied WITHOUT bases. The pictures show a digital render. Printed and painted models by Red Copper Miniatures. The 3D files are from Red Copper Miniatures. These 3D files are produced and sold under a commercial licence. Most of the miniatures are printed after you order them. The long processing time allows me to sensibly plan my working and printing time. Whenever possible, I try to cut the processing time short. The models are delivered unpainted and unassambled. This is a 3D printed product made of UV hardened resin. Models are cleaned and completely cured with UV light. Before printing, a support structure needs to be added to the models, these are normally removed after printing, but leave "scars" on the model. These are production-related and do not represent a defect in the product. Remains of the support structure might still be on the model and can be removed with a sharp hobby knife. Resin dust is a health hazard if inhaled into the lungs. Sanding and filing is not recommended. Otherwise, such work should only be carried out with appropriate protective equipment (fine dust mask) and/or wet sandpaper. It's possible that the models are hollow. In this case, the model has drainage holes through which the liquid resin could leak out. The inside of the model was then also cured. Drainage holes can be closed with modelling putty. Resin is heat-sensitive and can therefore deform during the printing process, the removal of the support structures, post-process curing, or shipping. Hot water or a heat gun/hair dryer can quickly remedy this. The affected part is heated and then carefully bent into the correct position. Important noticeWarning! Not for children under the age of 3. Choking hazard due to small parts.This product is not a toy.
From €6.00*
King Muwatalli II on heavy chariot
28 mm scale for collectors, painters and gamers, e.g. for Hail Caesar, Field of Glory, Triumph, Mortem et Gloriam, Impetus!, or other historical miniature wargames.Please note that the models are supplied WITHOUT bases. The pictures show a digital render. Printed and painted models by Red Copper Miniatures. The 3D files are from Red Copper Miniatures. These 3D files are produced and sold under a commercial licence. Most of the miniatures are printed after you order them. The long processing time allows me to sensibly plan my working and printing time. Whenever possible, I try to cut the processing time short. The models are delivered unpainted and unassambled. This is a 3D printed product made of UV hardened resin. Models are cleaned and completely cured with UV light. Before printing, a support structure needs to be added to the models, these are normally removed after printing, but leave "scars" on the model. These are production-related and do not represent a defect in the product. Remains of the support structure might still be on the model and can be removed with a sharp hobby knife. Resin dust is a health hazard if inhaled into the lungs. Sanding and filing is not recommended. Otherwise, such work should only be carried out with appropriate protective equipment (fine dust mask) and/or wet sandpaper. It's possible that the models are hollow. In this case, the model has drainage holes through which the liquid resin could leak out. The inside of the model was then also cured. Drainage holes can be closed with modelling putty. Resin is heat-sensitive and can therefore deform during the printing process, the removal of the support structures, post-process curing, or shipping. Hot water or a heat gun/hair dryer can quickly remedy this. The affected part is heated and then carefully bent into the correct position. Important noticeWarning! Not for children under the age of 3. Choking hazard due to small parts.This product is not a toy.
From €7.50*
King Ramesses II on chariot
28 mm scale for collectors, painters and gamers, e.g. for Hail Caesar, Field of Glory, Triumph, Mortem et Gloriam, Impetus!, or other historical miniature wargames.Please note that the models are supplied WITHOUT bases. The pictures show a digital render. Printed and painted models by Red Copper Miniatures. The 3D files are from Red Copper Miniatures. These 3D files are produced and sold under a commercial licence. Most of the miniatures are printed after you order them. The long processing time allows me to sensibly plan my working and printing time. Whenever possible, I try to cut the processing time short. The models are delivered unpainted and unassambled. This is a 3D printed product made of UV hardened resin. Models are cleaned and completely cured with UV light. Before printing, a support structure needs to be added to the models, these are normally removed after printing, but leave "scars" on the model. These are production-related and do not represent a defect in the product. Remains of the support structure might still be on the model and can be removed with a sharp hobby knife. Resin dust is a health hazard if inhaled into the lungs. Sanding and filing is not recommended. Otherwise, such work should only be carried out with appropriate protective equipment (fine dust mask) and/or wet sandpaper. It's possible that the models are hollow. In this case, the model has drainage holes through which the liquid resin could leak out. The inside of the model was then also cured. Drainage holes can be closed with modelling putty. Resin is heat-sensitive and can therefore deform during the printing process, the removal of the support structures, post-process curing, or shipping. Hot water or a heat gun/hair dryer can quickly remedy this. The affected part is heated and then carefully bent into the correct position. Important noticeWarning! Not for children under the age of 3. Choking hazard due to small parts.This product is not a toy.
From €7.00*
Libyan Warband (5 models)
28 mm scale for collectors, painters and gamers, e.g. for Hail Caesar, Field of Glory, Triumph, Mortem et Gloriam, Impetus!, or other historical miniature wargames.Please note that the models are supplied WITHOUT bases. The pictures show a digital render. Printed and painted models by Red Copper Miniatures. The 3D files are from Red Copper Miniatures. These 3D files are produced and sold under a commercial licence. Most of the miniatures are printed after you order them. The long processing time allows me to sensibly plan my working and printing time. Whenever possible, I try to cut the processing time short. The models are delivered unpainted and unassambled. This is a 3D printed product made of UV hardened resin. Models are cleaned and completely cured with UV light. Before printing, a support structure needs to be added to the models, these are normally removed after printing, but leave "scars" on the model. These are production-related and do not represent a defect in the product. Remains of the support structure might still be on the model and can be removed with a sharp hobby knife. Resin dust is a health hazard if inhaled into the lungs. Sanding and filing is not recommended. Otherwise, such work should only be carried out with appropriate protective equipment (fine dust mask) and/or wet sandpaper. It's possible that the models are hollow. In this case, the model has drainage holes through which the liquid resin could leak out. The inside of the model was then also cured. Drainage holes can be closed with modelling putty. Resin is heat-sensitive and can therefore deform during the printing process, the removal of the support structures, post-process curing, or shipping. Hot water or a heat gun/hair dryer can quickly remedy this. The affected part is heated and then carefully bent into the correct position. Important noticeWarning! Not for children under the age of 3. Choking hazard due to small parts.This product is not a toy.
From €6.00*
Nubian Skirmishers (5 models)
28 mm scale for collectors, painters and gamers, e.g. for Hail Caesar, Field of Glory, Triumph, Mortem et Gloriam, Impetus!, or other historical miniature wargames.Please note that the models are supplied WITHOUT bases. The pictures show a digital render. Printed and painted models by Red Copper Miniatures. The 3D files are from Red Copper Miniatures. These 3D files are produced and sold under a commercial licence. Most of the miniatures are printed after you order them. The long processing time allows me to sensibly plan my working and printing time. Whenever possible, I try to cut the processing time short. The models are delivered unpainted and unassambled. This is a 3D printed product made of UV hardened resin. Models are cleaned and completely cured with UV light. Before printing, a support structure needs to be added to the models, these are normally removed after printing, but leave "scars" on the model. These are production-related and do not represent a defect in the product. Remains of the support structure might still be on the model and can be removed with a sharp hobby knife. Resin dust is a health hazard if inhaled into the lungs. Sanding and filing is not recommended. Otherwise, such work should only be carried out with appropriate protective equipment (fine dust mask) and/or wet sandpaper. It's possible that the models are hollow. In this case, the model has drainage holes through which the liquid resin could leak out. The inside of the model was then also cured. Drainage holes can be closed with modelling putty. Resin is heat-sensitive and can therefore deform during the printing process, the removal of the support structures, post-process curing, or shipping. Hot water or a heat gun/hair dryer can quickly remedy this. The affected part is heated and then carefully bent into the correct position. Important noticeWarning! Not for children under the age of 3. Choking hazard due to small parts.This product is not a toy.
From €6.00*