2-Slot Bases 40x20 mm for 10 mm models on strips, e.g. for infantry and cavalry. One pack of 3 bases is usually used for one unit. The pictures show a digital render. The 3D files are from Forest Dragon. These 3D files are produced and sold under a commercial licence. Most of the miniatures are printed after you order them. The long processing time allows me to sensibly plan my working and printing time. Whenever possible, I try to cut the processing time short. The models are delivered unpainted and unassambled. This is a 3D printed product made of UV hardened resin. Models are cleaned and completely cured with UV light. Before printing, a support structure needs to be added to the models, these are normally removed after printing, but leave "scars" on the model. These are production-related and do not represent a defect in the product. Remains of the support structure might still be on the model and can be removed with a sharp hobby knife. Resin dust is a health hazard if inhaled into the lungs. Sanding and filing is not recommended. Otherwise, such work should only be carried out with appropriate protective equipment (fine dust mask) and/or wet sandpaper. It's possible that the models are hollow. In this case, the model has drainage holes through which the liquid resin could leak out. The inside of the model was then also cured. Drainage holes can be closed with modelling putty. Resin is heat-sensitive and can therefore deform during the printing process, the removal of the support structures, post-process curing, or shipping. Hot water or a heat gun/hair dryer can quickly remedy this. The affected part is heated and then carefully bent into the correct position. Important noticeWarning! Not for children under the age of 3. Choking hazard due to small parts.This product is not a toy.

2-Slot Bases 40x20 mm for 10 mm models on strips, e.g. for infantry and cavalry. One pack of 3 bases is usually used for one unit. The two slots are spaced further apart to give more room to bigger models like Orcs. The pictures show a digital render. The 3D files are from Forest Dragon. These 3D files are produced and sold under a commercial licence. Most of the miniatures are printed after you order them. The long processing time allows me to sensibly plan my working and printing time. Whenever possible, I try to cut the processing time short. The models are delivered unpainted and unassambled. This is a 3D printed product made of UV hardened resin. Models are cleaned and completely cured with UV light. Before printing, a support structure needs to be added to the models, these are normally removed after printing, but leave "scars" on the model. These are production-related and do not represent a defect in the product. Remains of the support structure might still be on the model and can be removed with a sharp hobby knife. Resin dust is a health hazard if inhaled into the lungs. Sanding and filing is not recommended. Otherwise, such work should only be carried out with appropriate protective equipment (fine dust mask) and/or wet sandpaper. It's possible that the models are hollow. In this case, the model has drainage holes through which the liquid resin could leak out. The inside of the model was then also cured. Drainage holes can be closed with modelling putty. Resin is heat-sensitive and can therefore deform during the printing process, the removal of the support structures, post-process curing, or shipping. Hot water or a heat gun/hair dryer can quickly remedy this. The affected part is heated and then carefully bent into the correct position. Important noticeWarning! Not for children under the age of 3. Choking hazard due to small parts.This product is not a toy.

25 mm base with bevelled edge. Magnet holder for round magnet on the bottom. Alternatively as a slotta base.With a layer height of 0.08 mm, the typical stair effect of FDM prints is only barely visible.Colour: Black The pictures show a printed product, often in conjunction with additional digital render images. The prints are usually without final cleanup, but as delievered. The final colour of the material may differ. Most of the miniatures are printed after you order them. The long processing time allows me to sensibly plan my working and printing time. Whenever possible, I try to cut the processing time short. The models are delivered unpainted and unassambled. This is a 3D printed product made of PLA filament (FDM print). Before printing, a support structure may need to be added to the product. These are usually removed after printing, but leave "scars". The product may also have small bumps and grooves. With FDM printing, layer line are also visible. All of this is production-related and does not represent a defect in the product PLA dust is a health hazard if inhaled into the lungs. Sanding and filing should only be carried out with appropriate protective equipment (fine dust mask) and/or wet sandpaper. The product is filled with a filling pattern on the inside, it is not a completely solid product. The product must not be used in direct sunlight or near heat sources. PLA is sensitive to heat and can deform when exposed to heat and sunlight. Deformation is permanent and an user error.PLA waste must be disposed of in household waste; despite often stated otherwise, it is not readily biodegradable. Important noticeWarning! Not for children under the age of 3. Choking hazard due to small parts.This product is not a toy.

28 mm base with bevelled edge. Magnet holder for round magnet on the bottom. Alternatively as a slotta base.With a layer height of 0.08 mm, the typical stair effect of FDM prints is only barely visible.Colour: Black The pictures show a printed product, often in conjunction with additional digital render images. The prints are usually without final cleanup, but as delievered. The final colour of the material may differ. Most of the miniatures are printed after you order them. The long processing time allows me to sensibly plan my working and printing time. Whenever possible, I try to cut the processing time short. The models are delivered unpainted and unassambled. This is a 3D printed product made of PLA filament (FDM print). Before printing, a support structure may need to be added to the product. These are usually removed after printing, but leave "scars". The product may also have small bumps and grooves. With FDM printing, layer line are also visible. All of this is production-related and does not represent a defect in the product PLA dust is a health hazard if inhaled into the lungs. Sanding and filing should only be carried out with appropriate protective equipment (fine dust mask) and/or wet sandpaper. The product is filled with a filling pattern on the inside, it is not a completely solid product. The product must not be used in direct sunlight or near heat sources. PLA is sensitive to heat and can deform when exposed to heat and sunlight. Deformation is permanent and an user error.PLA waste must be disposed of in household waste; despite often stated otherwise, it is not readily biodegradable. Important noticeWarning! Not for children under the age of 3. Choking hazard due to small parts.This product is not a toy.

3-Round Slot Bases 40x20 mm for 10 mm models on round bases, e.g. for Monstrous Infantry. One pack of 3 bases is usually used for one unit. The pictures show a digital render. The 3D files are from Forest Dragon. These 3D files are produced and sold under a commercial licence. Most of the miniatures are printed after you order them. The long processing time allows me to sensibly plan my working and printing time. Whenever possible, I try to cut the processing time short. The models are delivered unpainted and unassambled. This is a 3D printed product made of UV hardened resin. Models are cleaned and completely cured with UV light. Before printing, a support structure needs to be added to the models, these are normally removed after printing, but leave "scars" on the model. These are production-related and do not represent a defect in the product. Remains of the support structure might still be on the model and can be removed with a sharp hobby knife. Resin dust is a health hazard if inhaled into the lungs. Sanding and filing is not recommended. Otherwise, such work should only be carried out with appropriate protective equipment (fine dust mask) and/or wet sandpaper. It's possible that the models are hollow. In this case, the model has drainage holes through which the liquid resin could leak out. The inside of the model was then also cured. Drainage holes can be closed with modelling putty. Resin is heat-sensitive and can therefore deform during the printing process, the removal of the support structures, post-process curing, or shipping. Hot water or a heat gun/hair dryer can quickly remedy this. The affected part is heated and then carefully bent into the correct position. Important noticeWarning! Not for children under the age of 3. Choking hazard due to small parts.This product is not a toy.

30 mm base with bevelled edge. Magnet holder for round magnet on the bottom. Alternatively as a slotta base.With a layer height of 0.08 mm, the typical stair effect of FDM prints is only barely visible.Colour: Black The pictures show a printed product, often in conjunction with additional digital render images. The prints are usually without final cleanup, but as delievered. The final colour of the material may differ. Most of the miniatures are printed after you order them. The long processing time allows me to sensibly plan my working and printing time. Whenever possible, I try to cut the processing time short. The models are delivered unpainted and unassambled. This is a 3D printed product made of PLA filament (FDM print). Before printing, a support structure may need to be added to the product. These are usually removed after printing, but leave "scars". The product may also have small bumps and grooves. With FDM printing, layer line are also visible. All of this is production-related and does not represent a defect in the product PLA dust is a health hazard if inhaled into the lungs. Sanding and filing should only be carried out with appropriate protective equipment (fine dust mask) and/or wet sandpaper. The product is filled with a filling pattern on the inside, it is not a completely solid product. The product must not be used in direct sunlight or near heat sources. PLA is sensitive to heat and can deform when exposed to heat and sunlight. Deformation is permanent and an user error.PLA waste must be disposed of in household waste; despite often stated otherwise, it is not readily biodegradable. Important noticeWarning! Not for children under the age of 3. Choking hazard due to small parts.This product is not a toy.

Bases and stems made from colourless transparent acrylic. Stems according to choice "short" (15 and 20 mm) and/or "long" (30 and 35 mm). The stems may include production related air bubbles and don't represent a defect in the product.

32 mm base with bevelled edge. Magnet holder for round magnet on the bottom. Alternatively as a slotta base.With a layer height of 0.08 mm, the typical stair effect of FDM prints is only barely visible.Colour: Black The pictures show a printed product, often in conjunction with additional digital render images. The prints are usually without final cleanup, but as delievered. The final colour of the material may differ. Most of the miniatures are printed after you order them. The long processing time allows me to sensibly plan my working and printing time. Whenever possible, I try to cut the processing time short. The models are delivered unpainted and unassambled. This is a 3D printed product made of PLA filament (FDM print). Before printing, a support structure may need to be added to the product. These are usually removed after printing, but leave "scars". The product may also have small bumps and grooves. With FDM printing, layer line are also visible. All of this is production-related and does not represent a defect in the product PLA dust is a health hazard if inhaled into the lungs. Sanding and filing should only be carried out with appropriate protective equipment (fine dust mask) and/or wet sandpaper. The product is filled with a filling pattern on the inside, it is not a completely solid product. The product must not be used in direct sunlight or near heat sources. PLA is sensitive to heat and can deform when exposed to heat and sunlight. Deformation is permanent and an user error.PLA waste must be disposed of in household waste; despite often stated otherwise, it is not readily biodegradable. Important noticeWarning! Not for children under the age of 3. Choking hazard due to small parts.This product is not a toy.

32 mm Base mit 3 mm Loch für Flugstab aus Acryl, Messing, etc. und Markierungen für verschiedene Sektoren und/oder Feuerwinkel. Die Base eignet sich damit perfekt für Spiele wie z.B. Battlefleet Gothic, Full Thrust, Dropfleet Commander oder sonstige Science Fiction Raumschiff Tabletop-Spiele. The pictures show a digital render. The 3D files are from Keiler. These 3D files are produced and sold under a commercial licence. Most of the miniatures are printed after you order them. The long processing time allows me to sensibly plan my working and printing time. Whenever possible, I try to cut the processing time short. The models are delivered unpainted and unassambled. This is a 3D printed product made of UV hardened resin. Models are cleaned and completely cured with UV light. Before printing, a support structure needs to be added to the models, these are normally removed after printing, but leave "scars" on the model. These are production-related and do not represent a defect in the product. Remains of the support structure might still be on the model and can be removed with a sharp hobby knife. Resin dust is a health hazard if inhaled into the lungs. Sanding and filing is not recommended. Otherwise, such work should only be carried out with appropriate protective equipment (fine dust mask) and/or wet sandpaper. It's possible that the models are hollow. In this case, the model has drainage holes through which the liquid resin could leak out. The inside of the model was then also cured. Drainage holes can be closed with modelling putty. Resin is heat-sensitive and can therefore deform during the printing process, the removal of the support structures, post-process curing, or shipping. Hot water or a heat gun/hair dryer can quickly remedy this. The affected part is heated and then carefully bent into the correct position. Important noticeWarning! Not for children under the age of 3. Choking hazard due to small parts.This product is not a toy.

39 mm base (equals the "40 mm" base of a big hobby manufacturer) with bevelled edge. Two magnet holders for round magnets on the bottom.With a layer height of 0.08 mm, the typical stair effect of FDM prints is only barely visible.Colour: Black The pictures show a printed product, often in conjunction with additional digital render images. The prints are usually without final cleanup, but as delievered. The final colour of the material may differ. Most of the miniatures are printed after you order them. The long processing time allows me to sensibly plan my working and printing time. Whenever possible, I try to cut the processing time short. The models are delivered unpainted and unassambled. This is a 3D printed product made of PLA filament (FDM print). Before printing, a support structure may need to be added to the product. These are usually removed after printing, but leave "scars". The product may also have small bumps and grooves. With FDM printing, layer line are also visible. All of this is production-related and does not represent a defect in the product PLA dust is a health hazard if inhaled into the lungs. Sanding and filing should only be carried out with appropriate protective equipment (fine dust mask) and/or wet sandpaper. The product is filled with a filling pattern on the inside, it is not a completely solid product. The product must not be used in direct sunlight or near heat sources. PLA is sensitive to heat and can deform when exposed to heat and sunlight. Deformation is permanent and an user error.PLA waste must be disposed of in household waste; despite often stated otherwise, it is not readily biodegradable. Important noticeWarning! Not for children under the age of 3. Choking hazard due to small parts.This product is not a toy.

4-Slot Bases 20x40 mm for 10 mm models on strips, e.g. for ranged infantry. One pack of 3 bases is usually used for one unit. The pictures show a digital render. The 3D files are from Forest Dragon. These 3D files are produced and sold under a commercial licence. Most of the miniatures are printed after you order them. The long processing time allows me to sensibly plan my working and printing time. Whenever possible, I try to cut the processing time short. The models are delivered unpainted and unassambled. This is a 3D printed product made of UV hardened resin. Models are cleaned and completely cured with UV light. Before printing, a support structure needs to be added to the models, these are normally removed after printing, but leave "scars" on the model. These are production-related and do not represent a defect in the product. Remains of the support structure might still be on the model and can be removed with a sharp hobby knife. Resin dust is a health hazard if inhaled into the lungs. Sanding and filing is not recommended. Otherwise, such work should only be carried out with appropriate protective equipment (fine dust mask) and/or wet sandpaper. It's possible that the models are hollow. In this case, the model has drainage holes through which the liquid resin could leak out. The inside of the model was then also cured. Drainage holes can be closed with modelling putty. Resin is heat-sensitive and can therefore deform during the printing process, the removal of the support structures, post-process curing, or shipping. Hot water or a heat gun/hair dryer can quickly remedy this. The affected part is heated and then carefully bent into the correct position. Important noticeWarning! Not for children under the age of 3. Choking hazard due to small parts.This product is not a toy.

Base and stems made from colourless transparent acrylic. Stems according to choice "short" (15 and 20 mm) or "long" (30 and 35 mm). The stems may include production related air bubbles and don't represent a defect in the product.

60 mm Base mit 3 mm Loch für Flugstab aus Acryl, Messing, etc. und Markierungen für verschiedene Sektoren und/oder Feuerwinkel. Die Base eignet sich damit perfekt für Spiele wie z.B. Battlefleet Gothic, Full Thrust, Dropfleet Commander oder sonstige Science Fiction Raumschiff Tabletop-Spiele. The pictures show a digital render. The 3D files are from Keiler. These 3D files are produced and sold under a commercial licence. Most of the miniatures are printed after you order them. The long processing time allows me to sensibly plan my working and printing time. Whenever possible, I try to cut the processing time short. The models are delivered unpainted and unassambled. This is a 3D printed product made of UV hardened resin. Models are cleaned and completely cured with UV light. Before printing, a support structure needs to be added to the models, these are normally removed after printing, but leave "scars" on the model. These are production-related and do not represent a defect in the product. Remains of the support structure might still be on the model and can be removed with a sharp hobby knife. Resin dust is a health hazard if inhaled into the lungs. Sanding and filing is not recommended. Otherwise, such work should only be carried out with appropriate protective equipment (fine dust mask) and/or wet sandpaper. It's possible that the models are hollow. In this case, the model has drainage holes through which the liquid resin could leak out. The inside of the model was then also cured. Drainage holes can be closed with modelling putty. Resin is heat-sensitive and can therefore deform during the printing process, the removal of the support structures, post-process curing, or shipping. Hot water or a heat gun/hair dryer can quickly remedy this. The affected part is heated and then carefully bent into the correct position. Important noticeWarning! Not for children under the age of 3. Choking hazard due to small parts.This product is not a toy.

90 mm Base mit 6,35 mm (1/4 Zoll) Loch für Flugstab aus Acryl, Messing, etc. und Markierungen für verschiedene Sektoren und/oder Feuerwinkel. Die Base eignet sich damit perfekt für Spiele wie z.B. Battlefleet Gothic, Full Thrust, Dropfleet Commander oder sonstige Science Fiction Raumschiff Tabletop-Spiele. The pictures show a digital render. The 3D files are from Keiler. These 3D files are produced and sold under a commercial licence. Most of the miniatures are printed after you order them. The long processing time allows me to sensibly plan my working and printing time. Whenever possible, I try to cut the processing time short. The models are delivered unpainted and unassambled. This is a 3D printed product made of UV hardened resin. Models are cleaned and completely cured with UV light. Before printing, a support structure needs to be added to the models, these are normally removed after printing, but leave "scars" on the model. These are production-related and do not represent a defect in the product. Remains of the support structure might still be on the model and can be removed with a sharp hobby knife. Resin dust is a health hazard if inhaled into the lungs. Sanding and filing is not recommended. Otherwise, such work should only be carried out with appropriate protective equipment (fine dust mask) and/or wet sandpaper. It's possible that the models are hollow. In this case, the model has drainage holes through which the liquid resin could leak out. The inside of the model was then also cured. Drainage holes can be closed with modelling putty. Resin is heat-sensitive and can therefore deform during the printing process, the removal of the support structures, post-process curing, or shipping. Hot water or a heat gun/hair dryer can quickly remedy this. The affected part is heated and then carefully bent into the correct position. Important noticeWarning! Not for children under the age of 3. Choking hazard due to small parts.This product is not a toy.

Flyer base with 2 mm hole for an acrylic, brass, etc. rodand markings for different sections or fire arcs. This makes base perfectly fitted for games like Battlefleet Gothic, Firestorm Armada, Full Thrust, A Billion Suns, Warfleets: FTL, Dropfleet Commander or other Science Fiction spaceship miniature wargames. Please note that the models are supplied WITHOUT bases. The 3D files are from NofixedForge. These 3D files are produced and sold under a commercial licence. Printed and painted model by NofixedForge. Most of the miniatures are printed after you order them. The long processing time allows me to sensibly plan my working and printing time. Whenever possible, I try to cut the processing time short. The models are delivered unpainted and unassambled. This is a 3D printed product made of UV hardened resin. Models are cleaned and completely cured with UV light. Before printing, a support structure needs to be added to the models, these are normally removed after printing, but leave "scars" on the model. These are production-related and do not represent a defect in the product. Remains of the support structure might still be on the model and can be removed with a sharp hobby knife. Resin dust is a health hazard if inhaled into the lungs. Sanding and filing is not recommended. Otherwise, such work should only be carried out with appropriate protective equipment (fine dust mask) and/or wet sandpaper. It's possible that the models are hollow. In this case, the model has drainage holes through which the liquid resin could leak out. The inside of the model was then also cured. Drainage holes can be closed with modelling putty. Resin is heat-sensitive and can therefore deform during the printing process, the removal of the support structures, post-process curing, or shipping. Hot water or a heat gun/hair dryer can quickly remedy this. The affected part is heated and then carefully bent into the correct position. Important noticeWarning! Not for children under the age of 3. Choking hazard due to small parts.This product is not a toy.

10x flying stems with 4 mm ball head. Suitable for spaceship models from Edge Miniatures.The pictures show a digital render. The 3D files are from Edge Miniatures. These 3D files are produced and sold under a commercial licence. Most of the miniatures are printed after you order them. The long processing time allows me to sensibly plan my working and printing time. Whenever possible, I try to cut the processing time short. The models are delivered unpainted and unassambled. This is a 3D printed product made of UV hardened resin. Models are cleaned and completely cured with UV light. Before printing, a support structure needs to be added to the models, these are normally removed after printing, but leave "scars" on the model. These are production-related and do not represent a defect in the product. Remains of the support structure might still be on the model and can be removed with a sharp hobby knife. Resin dust is a health hazard if inhaled into the lungs. Sanding and filing is not recommended. Otherwise, such work should only be carried out with appropriate protective equipment (fine dust mask) and/or wet sandpaper. It's possible that the models are hollow. In this case, the model has drainage holes through which the liquid resin could leak out. The inside of the model was then also cured. Drainage holes can be closed with modelling putty. Resin is heat-sensitive and can therefore deform during the printing process, the removal of the support structures, post-process curing, or shipping. Hot water or a heat gun/hair dryer can quickly remedy this. The affected part is heated and then carefully bent into the correct position. Important noticeWarning! Not for children under the age of 3. Choking hazard due to small parts.This product is not a toy.