28 mm scale for collectors, painters and gamers, e.g. for Zona Alfa, Scrappers, Five Klicks from the Zone, 7TV Apocalypse, Wreck Age, This is not a test, or similar miniature wargames in apocalyptic or post-apocalyptic setting. Please note that the models are supplied WITHOUT bases. The pictures show a digital render.The 3D files are created by TurnBase Miniatures. These 3D files are produced and sold under a commercial licence. Most of the miniatures are printed after you order them. The long processing time allows me to sensibly plan my working and printing time. Whenever possible, I try to cut the processing time short. The models are delivered unpainted and unassambled. This is a 3D printed product made of UV hardened resin. Models are cleaned and completely cured with UV light. Before printing, a support structure needs to be added to the models, these are normally removed after printing, but leave "scars" on the model. These are production-related and do not represent a defect in the product. Remains of the support structure might still be on the model and can be removed with a sharp hobby knife. Resin dust is a health hazard if inhaled into the lungs. Sanding and filing is not recommended. Otherwise, such work should only be carried out with appropriate protective equipment (fine dust mask) and/or wet sandpaper. It's possible that the models are hollow. In this case, the model has drainage holes through which the liquid resin could leak out. The inside of the model was then also cured. Drainage holes can be closed with modelling putty. Resin is heat-sensitive and can therefore deform during the printing process, the removal of the support structures, post-process curing, or shipping. Hot water or a heat gun/hair dryer can quickly remedy this. The affected part is heated and then carefully bent into the correct position. Important noticeWarning! Not for children under the age of 3. Choking hazard due to small parts.This product is not a toy.

28 mm scale for collectors, painters and gamers, e.g. for Zona Alfa, Scrappers, Five Klicks from the Zone, 7TV Apocalypse, Wreck Age, This is not a test, or similar miniature wargames in apocalyptic or post-apocalyptic setting. Please note that the models are supplied WITHOUT bases. The pictures show a digital render.The 3D files are created by TurnBase Miniatures. These 3D files are produced and sold under a commercial licence. Most of the miniatures are printed after you order them. The long processing time allows me to sensibly plan my working and printing time. Whenever possible, I try to cut the processing time short. The models are delivered unpainted and unassambled. This is a 3D printed product made of UV hardened resin. Models are cleaned and completely cured with UV light. Before printing, a support structure needs to be added to the models, these are normally removed after printing, but leave "scars" on the model. These are production-related and do not represent a defect in the product. Remains of the support structure might still be on the model and can be removed with a sharp hobby knife. Resin dust is a health hazard if inhaled into the lungs. Sanding and filing is not recommended. Otherwise, such work should only be carried out with appropriate protective equipment (fine dust mask) and/or wet sandpaper. It's possible that the models are hollow. In this case, the model has drainage holes through which the liquid resin could leak out. The inside of the model was then also cured. Drainage holes can be closed with modelling putty. Resin is heat-sensitive and can therefore deform during the printing process, the removal of the support structures, post-process curing, or shipping. Hot water or a heat gun/hair dryer can quickly remedy this. The affected part is heated and then carefully bent into the correct position. Important noticeWarning! Not for children under the age of 3. Choking hazard due to small parts.This product is not a toy.

28 mm scale for collectors, painters and gamers, e.g. for Spectre: Operations, Asymmetric Warfare, InCountry, Force on Force, Black Ops, Danger Close, Fireteam Modern or similar miniature wargames in modern or ultramodern setting. Please note that the models are supplied WITHOUT bases. The pictures show a digital render.The 3D files are from Miska Miniatures. These 3D files are produced and sold under a commercial licence. Most of the miniatures are printed after you order them. The long processing time allows me to sensibly plan my working and printing time. Whenever possible, I try to cut the processing time short. The models are delivered unpainted and unassambled. This is a 3D printed product made of UV hardened resin. Models are cleaned and completely cured with UV light. Before printing, a support structure needs to be added to the models, these are normally removed after printing, but leave "scars" on the model. These are production-related and do not represent a defect in the product. Remains of the support structure might still be on the model and can be removed with a sharp hobby knife. Resin dust is a health hazard if inhaled into the lungs. Sanding and filing is not recommended. Otherwise, such work should only be carried out with appropriate protective equipment (fine dust mask) and/or wet sandpaper. It's possible that the models are hollow. In this case, the model has drainage holes through which the liquid resin could leak out. The inside of the model was then also cured. Drainage holes can be closed with modelling putty. Resin is heat-sensitive and can therefore deform during the printing process, the removal of the support structures, post-process curing, or shipping. Hot water or a heat gun/hair dryer can quickly remedy this. The affected part is heated and then carefully bent into the correct position. Important noticeWarning! Not for children under the age of 3. Choking hazard due to small parts.This product is not a toy.

28 mm scale for collectors, painters and gamers, e.g. for Spectre: Operations, Asymmetric Warfare, InCountry, Force on Force, Black Ops, Danger Close, Fireteam Modern or similar miniature wargames in modern or ultramodern setting. Please note that the models are supplied WITHOUT bases. The pictures show a digital render.The 3D files are from Miska Miniatures. These 3D files are produced and sold under a commercial licence. Most of the miniatures are printed after you order them. The long processing time allows me to sensibly plan my working and printing time. Whenever possible, I try to cut the processing time short. The models are delivered unpainted and unassambled. This is a 3D printed product made of UV hardened resin. Models are cleaned and completely cured with UV light. Before printing, a support structure needs to be added to the models, these are normally removed after printing, but leave "scars" on the model. These are production-related and do not represent a defect in the product. Remains of the support structure might still be on the model and can be removed with a sharp hobby knife. Resin dust is a health hazard if inhaled into the lungs. Sanding and filing is not recommended. Otherwise, such work should only be carried out with appropriate protective equipment (fine dust mask) and/or wet sandpaper. It's possible that the models are hollow. In this case, the model has drainage holes through which the liquid resin could leak out. The inside of the model was then also cured. Drainage holes can be closed with modelling putty. Resin is heat-sensitive and can therefore deform during the printing process, the removal of the support structures, post-process curing, or shipping. Hot water or a heat gun/hair dryer can quickly remedy this. The affected part is heated and then carefully bent into the correct position. Important noticeWarning! Not for children under the age of 3. Choking hazard due to small parts.This product is not a toy.

28 mm Maßstab für Sammler, Maler und Spieler, z.B. für Spectre: Operations, Force on Force, Black Ops, Danger Close, Fireteam Modern oder ähnliche moderne Tabletop Spiele.Please note that the models are supplied WITHOUT bases. The pictures show a digital render.The 3D file are from Quartermaster3D. These 3D files are produced and sold under a commercial licence. Most of the miniatures are printed after you order them. The long processing time allows me to sensibly plan my working and printing time. Whenever possible, I try to cut the processing time short. The models are delivered unpainted and unassambled. This is a 3D printed product made of UV hardened resin. Models are cleaned and completely cured with UV light. Before printing, a support structure needs to be added to the models, these are normally removed after printing, but leave "scars" on the model. These are production-related and do not represent a defect in the product. Remains of the support structure might still be on the model and can be removed with a sharp hobby knife. Resin dust is a health hazard if inhaled into the lungs. Sanding and filing is not recommended. Otherwise, such work should only be carried out with appropriate protective equipment (fine dust mask) and/or wet sandpaper. It's possible that the models are hollow. In this case, the model has drainage holes through which the liquid resin could leak out. The inside of the model was then also cured. Drainage holes can be closed with modelling putty. Resin is heat-sensitive and can therefore deform during the printing process, the removal of the support structures, post-process curing, or shipping. Hot water or a heat gun/hair dryer can quickly remedy this. The affected part is heated and then carefully bent into the correct position. Important noticeWarning! Not for children under the age of 3. Choking hazard due to small parts.This product is not a toy.

28 mm Maßstab für Sammler, Maler und Spieler, z.B. für Spectre: Operations, Force on Force, Black Ops, Danger Close, Fireteam Modern oder ähnliche moderne Tabletop Spiele.Please note that the models are supplied WITHOUT bases. The pictures show a digital render.The 3D file are from Quartermaster3D. These 3D files are produced and sold under a commercial licence. Most of the miniatures are printed after you order them. The long processing time allows me to sensibly plan my working and printing time. Whenever possible, I try to cut the processing time short. The models are delivered unpainted and unassambled. This is a 3D printed product made of UV hardened resin. Models are cleaned and completely cured with UV light. Before printing, a support structure needs to be added to the models, these are normally removed after printing, but leave "scars" on the model. These are production-related and do not represent a defect in the product. Remains of the support structure might still be on the model and can be removed with a sharp hobby knife. Resin dust is a health hazard if inhaled into the lungs. Sanding and filing is not recommended. Otherwise, such work should only be carried out with appropriate protective equipment (fine dust mask) and/or wet sandpaper. It's possible that the models are hollow. In this case, the model has drainage holes through which the liquid resin could leak out. The inside of the model was then also cured. Drainage holes can be closed with modelling putty. Resin is heat-sensitive and can therefore deform during the printing process, the removal of the support structures, post-process curing, or shipping. Hot water or a heat gun/hair dryer can quickly remedy this. The affected part is heated and then carefully bent into the correct position. Important noticeWarning! Not for children under the age of 3. Choking hazard due to small parts.This product is not a toy.

Bring this legendary assassin to the tabletop and get revenge for his lost puppy. Scale as chosen; for collectors, painters and gamers, e.g. for Spectre: Operations, Asymmetric Warfare, InCountry, Force on Force, Black Ops, Danger Close, Fireteam Modern or similar miniature wargames in modern or ultramodern setting. Please note that the models are supplied WITHOUT bases. The pictures show a digital render.The 3D files are from Austin Miniatures. These 3D files are produced and sold under a commercial licence. Most of the miniatures are printed after you order them. The long processing time allows me to sensibly plan my working and printing time. Whenever possible, I try to cut the processing time short. The models are delivered unpainted and unassambled. This is a 3D printed product made of UV hardened resin. Models are cleaned and completely cured with UV light. Before printing, a support structure needs to be added to the models, these are normally removed after printing, but leave "scars" on the model. These are production-related and do not represent a defect in the product. Remains of the support structure might still be on the model and can be removed with a sharp hobby knife. Resin dust is a health hazard if inhaled into the lungs. Sanding and filing is not recommended. Otherwise, such work should only be carried out with appropriate protective equipment (fine dust mask) and/or wet sandpaper. It's possible that the models are hollow. In this case, the model has drainage holes through which the liquid resin could leak out. The inside of the model was then also cured. Drainage holes can be closed with modelling putty. Resin is heat-sensitive and can therefore deform during the printing process, the removal of the support structures, post-process curing, or shipping. Hot water or a heat gun/hair dryer can quickly remedy this. The affected part is heated and then carefully bent into the correct position. Important noticeWarning! Not for children under the age of 3. Choking hazard due to small parts.This product is not a toy.

28 mm scale for collectors, painters and gamers, e.g. for Spectre: Operations, Asymmetric Warfare, InCountry, Force on Force, Black Ops, Danger Close, Fireteam Modern or similar miniature wargames in modern or ultramodern setting. Please note that the models are supplied WITHOUT bases. The pictures show a digital render.The 3D files are created by TurnBase Miniatures. These 3D files are produced and sold under a commercial licence. Most of the miniatures are printed after you order them. The long processing time allows me to sensibly plan my working and printing time. Whenever possible, I try to cut the processing time short. The models are delivered unpainted and unassambled. This is a 3D printed product made of UV hardened resin. Models are cleaned and completely cured with UV light. Before printing, a support structure needs to be added to the models, these are normally removed after printing, but leave "scars" on the model. These are production-related and do not represent a defect in the product. Remains of the support structure might still be on the model and can be removed with a sharp hobby knife. Resin dust is a health hazard if inhaled into the lungs. Sanding and filing is not recommended. Otherwise, such work should only be carried out with appropriate protective equipment (fine dust mask) and/or wet sandpaper. It's possible that the models are hollow. In this case, the model has drainage holes through which the liquid resin could leak out. The inside of the model was then also cured. Drainage holes can be closed with modelling putty. Resin is heat-sensitive and can therefore deform during the printing process, the removal of the support structures, post-process curing, or shipping. Hot water or a heat gun/hair dryer can quickly remedy this. The affected part is heated and then carefully bent into the correct position. Important noticeWarning! Not for children under the age of 3. Choking hazard due to small parts.This product is not a toy.

28 mm scale for collectors, painters and gamers, e.g. for Zona Alfa, Scrappers, Five Klicks from the Zone, 7TV Apocalypse, Wreck Age, This is not a test, or similar miniature wargames in apocalyptic or post-apocalyptic setting. Please note that the models are supplied WITHOUT bases. The pictures show a digital render.The 3D files are created by TurnBase Miniatures. These 3D files are produced and sold under a commercial licence. Most of the miniatures are printed after you order them. The long processing time allows me to sensibly plan my working and printing time. Whenever possible, I try to cut the processing time short. The models are delivered unpainted and unassambled. This is a 3D printed product made of UV hardened resin. Models are cleaned and completely cured with UV light. Before printing, a support structure needs to be added to the models, these are normally removed after printing, but leave "scars" on the model. These are production-related and do not represent a defect in the product. Remains of the support structure might still be on the model and can be removed with a sharp hobby knife. Resin dust is a health hazard if inhaled into the lungs. Sanding and filing is not recommended. Otherwise, such work should only be carried out with appropriate protective equipment (fine dust mask) and/or wet sandpaper. It's possible that the models are hollow. In this case, the model has drainage holes through which the liquid resin could leak out. The inside of the model was then also cured. Drainage holes can be closed with modelling putty. Resin is heat-sensitive and can therefore deform during the printing process, the removal of the support structures, post-process curing, or shipping. Hot water or a heat gun/hair dryer can quickly remedy this. The affected part is heated and then carefully bent into the correct position. Important noticeWarning! Not for children under the age of 3. Choking hazard due to small parts.This product is not a toy.

28 mm scale for collectors, painters and gamers, e.g. for Zona Alfa, Scrappers, Five Klicks from the Zone, 7TV Apocalypse, Wreck Age, This is not a test, or similar miniature wargames in apocalyptic or post-apocalyptic setting. Please note that the models are supplied WITHOUT bases. The pictures show a digital render.The 3D files are created by TurnBase Miniatures. These 3D files are produced and sold under a commercial licence. Most of the miniatures are printed after you order them. The long processing time allows me to sensibly plan my working and printing time. Whenever possible, I try to cut the processing time short. The models are delivered unpainted and unassambled. This is a 3D printed product made of UV hardened resin. Models are cleaned and completely cured with UV light. Before printing, a support structure needs to be added to the models, these are normally removed after printing, but leave "scars" on the model. These are production-related and do not represent a defect in the product. Remains of the support structure might still be on the model and can be removed with a sharp hobby knife. Resin dust is a health hazard if inhaled into the lungs. Sanding and filing is not recommended. Otherwise, such work should only be carried out with appropriate protective equipment (fine dust mask) and/or wet sandpaper. It's possible that the models are hollow. In this case, the model has drainage holes through which the liquid resin could leak out. The inside of the model was then also cured. Drainage holes can be closed with modelling putty. Resin is heat-sensitive and can therefore deform during the printing process, the removal of the support structures, post-process curing, or shipping. Hot water or a heat gun/hair dryer can quickly remedy this. The affected part is heated and then carefully bent into the correct position. Important noticeWarning! Not for children under the age of 3. Choking hazard due to small parts.This product is not a toy.

28 mm scale for collectors, painters and gamers, e.g. for Spectre: Operations, Asymmetric Warfare, InCountry, Force on Force, Black Ops, Danger Close, Fireteam Modern or similar miniature wargames in modern or ultramodern setting. Please note that the models are supplied WITHOUT bases. The pictures show a digital render.The 3D files are from Black Hills Games. These 3D files are produced and sold under a commercial licence. Most of the miniatures are printed after you order them. The long processing time allows me to sensibly plan my working and printing time. Whenever possible, I try to cut the processing time short. The models are delivered unpainted and unassambled. This is a 3D printed product made of UV hardened resin. Models are cleaned and completely cured with UV light. Before printing, a support structure needs to be added to the models, these are normally removed after printing, but leave "scars" on the model. These are production-related and do not represent a defect in the product. Remains of the support structure might still be on the model and can be removed with a sharp hobby knife. Resin dust is a health hazard if inhaled into the lungs. Sanding and filing is not recommended. Otherwise, such work should only be carried out with appropriate protective equipment (fine dust mask) and/or wet sandpaper. It's possible that the models are hollow. In this case, the model has drainage holes through which the liquid resin could leak out. The inside of the model was then also cured. Drainage holes can be closed with modelling putty. Resin is heat-sensitive and can therefore deform during the printing process, the removal of the support structures, post-process curing, or shipping. Hot water or a heat gun/hair dryer can quickly remedy this. The affected part is heated and then carefully bent into the correct position. Important noticeWarning! Not for children under the age of 3. Choking hazard due to small parts.This product is not a toy.

28 mm Maßstab für Sammler, Maler und Spieler, z.B. für Spectre: Operations, Force on Force, Black Ops, Danger Close, Fireteam Modern oder ähnliche moderne Tabletop Spiele.Please note that the models are supplied WITHOUT bases. The pictures show a digital render.The 3D file are from Quartermaster3D. These 3D files are produced and sold under a commercial licence. Most of the miniatures are printed after you order them. The long processing time allows me to sensibly plan my working and printing time. Whenever possible, I try to cut the processing time short. The models are delivered unpainted and unassambled. This is a 3D printed product made of UV hardened resin. Models are cleaned and completely cured with UV light. Before printing, a support structure needs to be added to the models, these are normally removed after printing, but leave "scars" on the model. These are production-related and do not represent a defect in the product. Remains of the support structure might still be on the model and can be removed with a sharp hobby knife. Resin dust is a health hazard if inhaled into the lungs. Sanding and filing is not recommended. Otherwise, such work should only be carried out with appropriate protective equipment (fine dust mask) and/or wet sandpaper. It's possible that the models are hollow. In this case, the model has drainage holes through which the liquid resin could leak out. The inside of the model was then also cured. Drainage holes can be closed with modelling putty. Resin is heat-sensitive and can therefore deform during the printing process, the removal of the support structures, post-process curing, or shipping. Hot water or a heat gun/hair dryer can quickly remedy this. The affected part is heated and then carefully bent into the correct position. Important noticeWarning! Not for children under the age of 3. Choking hazard due to small parts.This product is not a toy.

28 mm scale for collectors, painters and gamers, e.g. for Spectre: Operations, Asymmetric Warfare, InCountry, Force on Force, Black Ops, Danger Close, Fireteam Modern or similar miniature wargames in modern or ultramodern setting. Please note that the models are supplied WITHOUT bases. The pictures show a digital render.The 3D files are from Miska Miniatures. These 3D files are produced and sold under a commercial licence. Most of the miniatures are printed after you order them. The long processing time allows me to sensibly plan my working and printing time. Whenever possible, I try to cut the processing time short. The models are delivered unpainted and unassambled. This is a 3D printed product made of UV hardened resin. Models are cleaned and completely cured with UV light. Before printing, a support structure needs to be added to the models, these are normally removed after printing, but leave "scars" on the model. These are production-related and do not represent a defect in the product. Remains of the support structure might still be on the model and can be removed with a sharp hobby knife. Resin dust is a health hazard if inhaled into the lungs. Sanding and filing is not recommended. Otherwise, such work should only be carried out with appropriate protective equipment (fine dust mask) and/or wet sandpaper. It's possible that the models are hollow. In this case, the model has drainage holes through which the liquid resin could leak out. The inside of the model was then also cured. Drainage holes can be closed with modelling putty. Resin is heat-sensitive and can therefore deform during the printing process, the removal of the support structures, post-process curing, or shipping. Hot water or a heat gun/hair dryer can quickly remedy this. The affected part is heated and then carefully bent into the correct position. Important noticeWarning! Not for children under the age of 3. Choking hazard due to small parts.This product is not a toy.

28 mm scale for collectors, painters and gamers, e.g. for Spectre: Operations, Asymmetric Warfare, InCountry, Force on Force, Black Ops, Danger Close, Fireteam Modern or similar miniature wargames in modern or ultramodern setting. Includes 4 different heads. The heads on the sniper and rocket launcher are fixed, they are single piece models. Please note that the models are supplied WITHOUT bases. The pictures show a digital render.The 3D files are created by TurnBase Miniatures. These 3D files are produced and sold under a commercial licence. Most of the miniatures are printed after you order them. The long processing time allows me to sensibly plan my working and printing time. Whenever possible, I try to cut the processing time short. The models are delivered unpainted and unassambled. This is a 3D printed product made of UV hardened resin. Models are cleaned and completely cured with UV light. Before printing, a support structure needs to be added to the models, these are normally removed after printing, but leave "scars" on the model. These are production-related and do not represent a defect in the product. Remains of the support structure might still be on the model and can be removed with a sharp hobby knife. Resin dust is a health hazard if inhaled into the lungs. Sanding and filing is not recommended. Otherwise, such work should only be carried out with appropriate protective equipment (fine dust mask) and/or wet sandpaper. It's possible that the models are hollow. In this case, the model has drainage holes through which the liquid resin could leak out. The inside of the model was then also cured. Drainage holes can be closed with modelling putty. Resin is heat-sensitive and can therefore deform during the printing process, the removal of the support structures, post-process curing, or shipping. Hot water or a heat gun/hair dryer can quickly remedy this. The affected part is heated and then carefully bent into the correct position. Important noticeWarning! Not for children under the age of 3. Choking hazard due to small parts.This product is not a toy.

28 mm scale for collectors, painters and gamers, e.g. for Spectre: Operations, Asymmetric Warfare, InCountry, Force on Force, Black Ops, Danger Close, Fireteam Modern or similar miniature wargames in modern or ultramodern setting. Please note that the models are supplied WITHOUT bases. The pictures show a digital render.The 3D files are from Miska Miniatures. These 3D files are produced and sold under a commercial licence. Most of the miniatures are printed after you order them. The long processing time allows me to sensibly plan my working and printing time. Whenever possible, I try to cut the processing time short. The models are delivered unpainted and unassambled. This is a 3D printed product made of UV hardened resin. Models are cleaned and completely cured with UV light. Before printing, a support structure needs to be added to the models, these are normally removed after printing, but leave "scars" on the model. These are production-related and do not represent a defect in the product. Remains of the support structure might still be on the model and can be removed with a sharp hobby knife. Resin dust is a health hazard if inhaled into the lungs. Sanding and filing is not recommended. Otherwise, such work should only be carried out with appropriate protective equipment (fine dust mask) and/or wet sandpaper. It's possible that the models are hollow. In this case, the model has drainage holes through which the liquid resin could leak out. The inside of the model was then also cured. Drainage holes can be closed with modelling putty. Resin is heat-sensitive and can therefore deform during the printing process, the removal of the support structures, post-process curing, or shipping. Hot water or a heat gun/hair dryer can quickly remedy this. The affected part is heated and then carefully bent into the correct position. Important noticeWarning! Not for children under the age of 3. Choking hazard due to small parts.This product is not a toy.

28 mm scale for collectors, painters and gamers, e.g. for Spectre: Operations, Asymmetric Warfare, InCountry, Force on Force, Black Ops, Danger Close, Fireteam Modern or similar miniature wargames in modern or ultramodern setting. Please note that the models are supplied WITHOUT bases. The pictures show a digital render.The 3D files are created by TurnBase Miniatures. These 3D files are produced and sold under a commercial licence. Most of the miniatures are printed after you order them. The long processing time allows me to sensibly plan my working and printing time. Whenever possible, I try to cut the processing time short. The models are delivered unpainted and unassambled. This is a 3D printed product made of UV hardened resin. Models are cleaned and completely cured with UV light. Before printing, a support structure needs to be added to the models, these are normally removed after printing, but leave "scars" on the model. These are production-related and do not represent a defect in the product. Remains of the support structure might still be on the model and can be removed with a sharp hobby knife. Resin dust is a health hazard if inhaled into the lungs. Sanding and filing is not recommended. Otherwise, such work should only be carried out with appropriate protective equipment (fine dust mask) and/or wet sandpaper. It's possible that the models are hollow. In this case, the model has drainage holes through which the liquid resin could leak out. The inside of the model was then also cured. Drainage holes can be closed with modelling putty. Resin is heat-sensitive and can therefore deform during the printing process, the removal of the support structures, post-process curing, or shipping. Hot water or a heat gun/hair dryer can quickly remedy this. The affected part is heated and then carefully bent into the correct position. Important noticeWarning! Not for children under the age of 3. Choking hazard due to small parts.This product is not a toy.

28 mm scale for collectors, painters and gamers, e.g. for Spectre: Operations, Asymmetric Warfare, InCountry, Force on Force, Black Ops, Danger Close, Fireteam Modern or similar miniature wargames in modern or ultramodern setting. Please note that the models are supplied WITHOUT bases. The pictures show a digital render.The 3D files are created by TurnBase Miniatures. These 3D files are produced and sold under a commercial licence. Most of the miniatures are printed after you order them. The long processing time allows me to sensibly plan my working and printing time. Whenever possible, I try to cut the processing time short. The models are delivered unpainted and unassambled. This is a 3D printed product made of UV hardened resin. Models are cleaned and completely cured with UV light. Before printing, a support structure needs to be added to the models, these are normally removed after printing, but leave "scars" on the model. These are production-related and do not represent a defect in the product. Remains of the support structure might still be on the model and can be removed with a sharp hobby knife. Resin dust is a health hazard if inhaled into the lungs. Sanding and filing is not recommended. Otherwise, such work should only be carried out with appropriate protective equipment (fine dust mask) and/or wet sandpaper. It's possible that the models are hollow. In this case, the model has drainage holes through which the liquid resin could leak out. The inside of the model was then also cured. Drainage holes can be closed with modelling putty. Resin is heat-sensitive and can therefore deform during the printing process, the removal of the support structures, post-process curing, or shipping. Hot water or a heat gun/hair dryer can quickly remedy this. The affected part is heated and then carefully bent into the correct position. Important noticeWarning! Not for children under the age of 3. Choking hazard due to small parts.This product is not a toy.

28 mm scale for collectors, painters and gamers, e.g. for Spectre: Operations, Asymmetric Warfare, InCountry, Force on Force, Black Ops, Danger Close, Fireteam Modern or similar miniature wargames in modern or ultramodern setting. Please note that the models are supplied WITHOUT bases. The pictures show a digital render.The 3D files are created by TurnBase Miniatures. These 3D files are produced and sold under a commercial licence. Most of the miniatures are printed after you order them. The long processing time allows me to sensibly plan my working and printing time. Whenever possible, I try to cut the processing time short. The models are delivered unpainted and unassambled. This is a 3D printed product made of UV hardened resin. Models are cleaned and completely cured with UV light. Before printing, a support structure needs to be added to the models, these are normally removed after printing, but leave "scars" on the model. These are production-related and do not represent a defect in the product. Remains of the support structure might still be on the model and can be removed with a sharp hobby knife. Resin dust is a health hazard if inhaled into the lungs. Sanding and filing is not recommended. Otherwise, such work should only be carried out with appropriate protective equipment (fine dust mask) and/or wet sandpaper. It's possible that the models are hollow. In this case, the model has drainage holes through which the liquid resin could leak out. The inside of the model was then also cured. Drainage holes can be closed with modelling putty. Resin is heat-sensitive and can therefore deform during the printing process, the removal of the support structures, post-process curing, or shipping. Hot water or a heat gun/hair dryer can quickly remedy this. The affected part is heated and then carefully bent into the correct position. Important noticeWarning! Not for children under the age of 3. Choking hazard due to small parts.This product is not a toy.

28 mm scale for collectors, painters and gamers, e.g. for Zona Alfa, Scrappers, Five Klicks from the Zone, 7TV Apocalypse, Wreck Age, This is not a test, or similar miniature wargames in apocalyptic or post-apocalyptic setting. Please note that the models are supplied WITHOUT bases. The pictures show a digital render.The 3D files are created by TurnBase Miniatures. These 3D files are produced and sold under a commercial licence. Most of the miniatures are printed after you order them. The long processing time allows me to sensibly plan my working and printing time. Whenever possible, I try to cut the processing time short. The models are delivered unpainted and unassambled. This is a 3D printed product made of UV hardened resin. Models are cleaned and completely cured with UV light. Before printing, a support structure needs to be added to the models, these are normally removed after printing, but leave "scars" on the model. These are production-related and do not represent a defect in the product. Remains of the support structure might still be on the model and can be removed with a sharp hobby knife. Resin dust is a health hazard if inhaled into the lungs. Sanding and filing is not recommended. Otherwise, such work should only be carried out with appropriate protective equipment (fine dust mask) and/or wet sandpaper. It's possible that the models are hollow. In this case, the model has drainage holes through which the liquid resin could leak out. The inside of the model was then also cured. Drainage holes can be closed with modelling putty. Resin is heat-sensitive and can therefore deform during the printing process, the removal of the support structures, post-process curing, or shipping. Hot water or a heat gun/hair dryer can quickly remedy this. The affected part is heated and then carefully bent into the correct position. Important noticeWarning! Not for children under the age of 3. Choking hazard due to small parts.This product is not a toy.

28 mm scale for collectors, painters and gamers, e.g. for Zona Alfa, Scrappers, Five Klicks from the Zone, 7TV Apocalypse, Wreck Age, This is not a test, or similar miniature wargames in apocalyptic or post-apocalyptic setting. Please note that the models are supplied WITHOUT bases. The pictures show a digital render.The 3D files are created by TurnBase Miniatures. These 3D files are produced and sold under a commercial licence. Most of the miniatures are printed after you order them. The long processing time allows me to sensibly plan my working and printing time. Whenever possible, I try to cut the processing time short. The models are delivered unpainted and unassambled. This is a 3D printed product made of UV hardened resin. Models are cleaned and completely cured with UV light. Before printing, a support structure needs to be added to the models, these are normally removed after printing, but leave "scars" on the model. These are production-related and do not represent a defect in the product. Remains of the support structure might still be on the model and can be removed with a sharp hobby knife. Resin dust is a health hazard if inhaled into the lungs. Sanding and filing is not recommended. Otherwise, such work should only be carried out with appropriate protective equipment (fine dust mask) and/or wet sandpaper. It's possible that the models are hollow. In this case, the model has drainage holes through which the liquid resin could leak out. The inside of the model was then also cured. Drainage holes can be closed with modelling putty. Resin is heat-sensitive and can therefore deform during the printing process, the removal of the support structures, post-process curing, or shipping. Hot water or a heat gun/hair dryer can quickly remedy this. The affected part is heated and then carefully bent into the correct position. Important noticeWarning! Not for children under the age of 3. Choking hazard due to small parts.This product is not a toy.

28 mm scale for collectors, painters and gamers, e.g. for Spectre: Operations, Asymmetric Warfare, InCountry, Force on Force, Black Ops, Danger Close, Fireteam Modern or similar miniature wargames in modern or ultramodern setting. Please note that the models are supplied WITHOUT bases. The pictures show a digital render.The 3D files are created by TurnBase Miniatures. These 3D files are produced and sold under a commercial licence. Most of the miniatures are printed after you order them. The long processing time allows me to sensibly plan my working and printing time. Whenever possible, I try to cut the processing time short. The models are delivered unpainted and unassambled. This is a 3D printed product made of UV hardened resin. Models are cleaned and completely cured with UV light. Before printing, a support structure needs to be added to the models, these are normally removed after printing, but leave "scars" on the model. These are production-related and do not represent a defect in the product. Remains of the support structure might still be on the model and can be removed with a sharp hobby knife. Resin dust is a health hazard if inhaled into the lungs. Sanding and filing is not recommended. Otherwise, such work should only be carried out with appropriate protective equipment (fine dust mask) and/or wet sandpaper. It's possible that the models are hollow. In this case, the model has drainage holes through which the liquid resin could leak out. The inside of the model was then also cured. Drainage holes can be closed with modelling putty. Resin is heat-sensitive and can therefore deform during the printing process, the removal of the support structures, post-process curing, or shipping. Hot water or a heat gun/hair dryer can quickly remedy this. The affected part is heated and then carefully bent into the correct position. Important noticeWarning! Not for children under the age of 3. Choking hazard due to small parts.This product is not a toy.

28 mm scale for collectors, painters and gamers, e.g. for Spectre: Operations, Force on Force, Black Ops, Danger Close, Fireteam Modern or other tabletop miniature wargames.Please note that the models are supplied WITHOUT bases. The pictures show a digital render.The 3D file are from Quartermaster3D. These 3D files are produced and sold under a commercial licence. Most of the miniatures are printed after you order them. The long processing time allows me to sensibly plan my working and printing time. Whenever possible, I try to cut the processing time short. The models are delivered unpainted and unassambled. This is a 3D printed product made of UV hardened resin. Models are cleaned and completely cured with UV light. Before printing, a support structure needs to be added to the models, these are normally removed after printing, but leave "scars" on the model. These are production-related and do not represent a defect in the product. Remains of the support structure might still be on the model and can be removed with a sharp hobby knife. Resin dust is a health hazard if inhaled into the lungs. Sanding and filing is not recommended. Otherwise, such work should only be carried out with appropriate protective equipment (fine dust mask) and/or wet sandpaper. It's possible that the models are hollow. In this case, the model has drainage holes through which the liquid resin could leak out. The inside of the model was then also cured. Drainage holes can be closed with modelling putty. Resin is heat-sensitive and can therefore deform during the printing process, the removal of the support structures, post-process curing, or shipping. Hot water or a heat gun/hair dryer can quickly remedy this. The affected part is heated and then carefully bent into the correct position. Important noticeWarning! Not for children under the age of 3. Choking hazard due to small parts.This product is not a toy.

28 mm Maßstab für Sammler, Maler und Spieler, z.B. für Spectre: Operations, Force on Force, Black Ops, Danger Close, Fireteam Modern oder ähnliche moderne Tabletop Spiele.Please note that the models are supplied WITHOUT bases. The pictures show a digital render.The 3D file are from Quartermaster3D. These 3D files are produced and sold under a commercial licence. Most of the miniatures are printed after you order them. The long processing time allows me to sensibly plan my working and printing time. Whenever possible, I try to cut the processing time short. The models are delivered unpainted and unassambled. This is a 3D printed product made of UV hardened resin. Models are cleaned and completely cured with UV light. Before printing, a support structure needs to be added to the models, these are normally removed after printing, but leave "scars" on the model. These are production-related and do not represent a defect in the product. Remains of the support structure might still be on the model and can be removed with a sharp hobby knife. Resin dust is a health hazard if inhaled into the lungs. Sanding and filing is not recommended. Otherwise, such work should only be carried out with appropriate protective equipment (fine dust mask) and/or wet sandpaper. It's possible that the models are hollow. In this case, the model has drainage holes through which the liquid resin could leak out. The inside of the model was then also cured. Drainage holes can be closed with modelling putty. Resin is heat-sensitive and can therefore deform during the printing process, the removal of the support structures, post-process curing, or shipping. Hot water or a heat gun/hair dryer can quickly remedy this. The affected part is heated and then carefully bent into the correct position. Important noticeWarning! Not for children under the age of 3. Choking hazard due to small parts.This product is not a toy.

28 mm Maßstab für Sammler, Maler und Spieler, z.B. für Spectre: Operations, Force on Force, Black Ops, Danger Close, Fireteam Modern oder ähnliche moderne Tabletop Spiele.Please note that the models are supplied WITHOUT bases. The pictures show a digital render.The 3D file are from Quartermaster3D. These 3D files are produced and sold under a commercial licence. Most of the miniatures are printed after you order them. The long processing time allows me to sensibly plan my working and printing time. Whenever possible, I try to cut the processing time short. The models are delivered unpainted and unassambled. This is a 3D printed product made of UV hardened resin. Models are cleaned and completely cured with UV light. Before printing, a support structure needs to be added to the models, these are normally removed after printing, but leave "scars" on the model. These are production-related and do not represent a defect in the product. Remains of the support structure might still be on the model and can be removed with a sharp hobby knife. Resin dust is a health hazard if inhaled into the lungs. Sanding and filing is not recommended. Otherwise, such work should only be carried out with appropriate protective equipment (fine dust mask) and/or wet sandpaper. It's possible that the models are hollow. In this case, the model has drainage holes through which the liquid resin could leak out. The inside of the model was then also cured. Drainage holes can be closed with modelling putty. Resin is heat-sensitive and can therefore deform during the printing process, the removal of the support structures, post-process curing, or shipping. Hot water or a heat gun/hair dryer can quickly remedy this. The affected part is heated and then carefully bent into the correct position. Important noticeWarning! Not for children under the age of 3. Choking hazard due to small parts.This product is not a toy.