Filter
–
Goblin Archers (10 models)
28 mm scale for collectors, painters and gamer, Fantasy mass battle system compatible models, like e.g. Warhammer Fantasy, The Old World, Age of Sigmar, Kings of War, Oathmark, Dragon Rampant, or other fantasy miniature wargames.Goblins have an eye height of approx. 18 mm.Please note that the models are supplied WITHOUT bases. The pictures show a digital render. The 3D files are from Peculiar Companions. These 3D files are produced and sold under a commercial licence. Most of the miniatures are printed after you order them. The long processing time allows me to sensibly plan my working and printing time. Whenever possible, I try to cut the processing time short. The models are delivered unpainted and unassambled. This is a 3D printed product made of UV hardened resin. Models are cleaned and completely cured with UV light. Before printing, a support structure needs to be added to the models, these are normally removed after printing, but leave "scars" on the model. These are production-related and do not represent a defect in the product. Remains of the support structure might still be on the model and can be removed with a sharp hobby knife. Resin dust is a health hazard if inhaled into the lungs. Sanding and filing is not recommended. Otherwise, such work should only be carried out with appropriate protective equipment (fine dust mask) and/or wet sandpaper. It's possible that the models are hollow. In this case, the model has drainage holes through which the liquid resin could leak out. The inside of the model was then also cured. Drainage holes can be closed with modelling putty. Resin is heat-sensitive and can therefore deform during the printing process, the removal of the support structures, post-process curing, or shipping. Hot water or a heat gun/hair dryer can quickly remedy this. The affected part is heated and then carefully bent into the correct position. Important noticeWarning! Not for children under the age of 3. Choking hazard due to small parts.This product is not a toy.
€11.00*
Goblin Blowgunners (10 models)
28 mm scale for collectors, painters and gamer, Fantasy mass battle system compatible models, like e.g. Warhammer Fantasy, The Old World, Age of Sigmar, Kings of War, Oathmark, Dragon Rampant, or other fantasy miniature wargames.Goblins have an eye height of approx. 18 mm.Please note that the models are supplied WITHOUT bases. The pictures show a digital render. The 3D files are from Peculiar Companions. These 3D files are produced and sold under a commercial licence. Most of the miniatures are printed after you order them. The long processing time allows me to sensibly plan my working and printing time. Whenever possible, I try to cut the processing time short. The models are delivered unpainted and unassambled. This is a 3D printed product made of UV hardened resin. Models are cleaned and completely cured with UV light. Before printing, a support structure needs to be added to the models, these are normally removed after printing, but leave "scars" on the model. These are production-related and do not represent a defect in the product. Remains of the support structure might still be on the model and can be removed with a sharp hobby knife. Resin dust is a health hazard if inhaled into the lungs. Sanding and filing is not recommended. Otherwise, such work should only be carried out with appropriate protective equipment (fine dust mask) and/or wet sandpaper. It's possible that the models are hollow. In this case, the model has drainage holes through which the liquid resin could leak out. The inside of the model was then also cured. Drainage holes can be closed with modelling putty. Resin is heat-sensitive and can therefore deform during the printing process, the removal of the support structures, post-process curing, or shipping. Hot water or a heat gun/hair dryer can quickly remedy this. The affected part is heated and then carefully bent into the correct position. Important noticeWarning! Not for children under the age of 3. Choking hazard due to small parts.This product is not a toy.
€11.00*
Goblin Infantry (10 models)
28 mm scale for collectors, painters and gamer, Fantasy mass battle system compatible models, like e.g. Warhammer Fantasy, The Old World, Age of Sigmar, Kings of War, Oathmark, Dragon Rampant, or other fantasy miniature wargames.Goblins have an eye height of approx. 18 mm.Contains 10x Goblins with spears (seven different variants, 3 random duplicates) and left hands of choice.Please note that the models are supplied WITHOUT bases. The pictures show a digital render. The 3D files are from Peculiar Companions. These 3D files are produced and sold under a commercial licence. Most of the miniatures are printed after you order them. The long processing time allows me to sensibly plan my working and printing time. Whenever possible, I try to cut the processing time short. The models are delivered unpainted and unassambled. This is a 3D printed product made of UV hardened resin. Models are cleaned and completely cured with UV light. Before printing, a support structure needs to be added to the models, these are normally removed after printing, but leave "scars" on the model. These are production-related and do not represent a defect in the product. Remains of the support structure might still be on the model and can be removed with a sharp hobby knife. Resin dust is a health hazard if inhaled into the lungs. Sanding and filing is not recommended. Otherwise, such work should only be carried out with appropriate protective equipment (fine dust mask) and/or wet sandpaper. It's possible that the models are hollow. In this case, the model has drainage holes through which the liquid resin could leak out. The inside of the model was then also cured. Drainage holes can be closed with modelling putty. Resin is heat-sensitive and can therefore deform during the printing process, the removal of the support structures, post-process curing, or shipping. Hot water or a heat gun/hair dryer can quickly remedy this. The affected part is heated and then carefully bent into the correct position. Important noticeWarning! Not for children under the age of 3. Choking hazard due to small parts.This product is not a toy.
€15.00*
Goblin Sharpshooter on Warthog
28 mm scale for collectors, painters and gamer, Fantasy mass battle system compatible models, like e.g. Warhammer Fantasy, The Old World, Age of Sigmar, Kings of War, Oathmark, Dragon Rampant, or other fantasy miniature wargames.Goblins have an eye height of approx. 18 mm.Please note that the models are supplied WITHOUT bases. The pictures show a digital render. The 3D files are from Peculiar Companions. These 3D files are produced and sold under a commercial licence. Most of the miniatures are printed after you order them. The long processing time allows me to sensibly plan my working and printing time. Whenever possible, I try to cut the processing time short. The models are delivered unpainted and unassambled. This is a 3D printed product made of UV hardened resin. Models are cleaned and completely cured with UV light. Before printing, a support structure needs to be added to the models, these are normally removed after printing, but leave "scars" on the model. These are production-related and do not represent a defect in the product. Remains of the support structure might still be on the model and can be removed with a sharp hobby knife. Resin dust is a health hazard if inhaled into the lungs. Sanding and filing is not recommended. Otherwise, such work should only be carried out with appropriate protective equipment (fine dust mask) and/or wet sandpaper. It's possible that the models are hollow. In this case, the model has drainage holes through which the liquid resin could leak out. The inside of the model was then also cured. Drainage holes can be closed with modelling putty. Resin is heat-sensitive and can therefore deform during the printing process, the removal of the support structures, post-process curing, or shipping. Hot water or a heat gun/hair dryer can quickly remedy this. The affected part is heated and then carefully bent into the correct position. Important noticeWarning! Not for children under the age of 3. Choking hazard due to small parts.This product is not a toy.
€7.00*
Goblin Warthog Cavalry (5 models)
28 mm scale for collectors, painters and gamer, Fantasy mass battle system compatible models, like e.g. Warhammer Fantasy, The Old World, Age of Sigmar, Kings of War, Oathmark, Dragon Rampant, or other fantasy miniature wargames.Goblins have an eye height of approx. 18 mm.Includes 5x lances (random assortment of four different variants) and 5x shields (random assortment of two different variants). Furthermore, 3x tactical rocks to use below the two warthogs that only have two legs on the ground.Please note that the models are supplied WITHOUT bases. The pictures show a digital render. The 3D files are from Peculiar Companions. These 3D files are produced and sold under a commercial licence. Most of the miniatures are printed after you order them. The long processing time allows me to sensibly plan my working and printing time. Whenever possible, I try to cut the processing time short. The models are delivered unpainted and unassambled. This is a 3D printed product made of UV hardened resin. Models are cleaned and completely cured with UV light. Before printing, a support structure needs to be added to the models, these are normally removed after printing, but leave "scars" on the model. These are production-related and do not represent a defect in the product. Remains of the support structure might still be on the model and can be removed with a sharp hobby knife. Resin dust is a health hazard if inhaled into the lungs. Sanding and filing is not recommended. Otherwise, such work should only be carried out with appropriate protective equipment (fine dust mask) and/or wet sandpaper. It's possible that the models are hollow. In this case, the model has drainage holes through which the liquid resin could leak out. The inside of the model was then also cured. Drainage holes can be closed with modelling putty. Resin is heat-sensitive and can therefore deform during the printing process, the removal of the support structures, post-process curing, or shipping. Hot water or a heat gun/hair dryer can quickly remedy this. The affected part is heated and then carefully bent into the correct position. Important noticeWarning! Not for children under the age of 3. Choking hazard due to small parts.This product is not a toy.
€15.00*
Orc Buffalo Cavalry (5 models)
28 mm scale for collectors, painters and gamer, Fantasy mass battle system compatible models, like e.g. Warhammer Fantasy, The Old World, Age of Sigmar, Kings of War, Oathmark, Dragon Rampant, or other fantasy miniature wargames.Orcs have an eye height of approx. 32 mm.Includes 5x swords as backup weapons, 5x shields (random assortment of two different variants) and 5x lances or 5x swords (random assortment of two different variants). Furthermore, 4x tactical rocks to use below the two bulls that only have one leg on the ground.Please note that the models are supplied WITHOUT bases. The pictures show a digital render. The 3D files are from Peculiar Companions. These 3D files are produced and sold under a commercial licence. Most of the miniatures are printed after you order them. The long processing time allows me to sensibly plan my working and printing time. Whenever possible, I try to cut the processing time short. The models are delivered unpainted and unassambled. This is a 3D printed product made of UV hardened resin. Models are cleaned and completely cured with UV light. Before printing, a support structure needs to be added to the models, these are normally removed after printing, but leave "scars" on the model. These are production-related and do not represent a defect in the product. Remains of the support structure might still be on the model and can be removed with a sharp hobby knife. Resin dust is a health hazard if inhaled into the lungs. Sanding and filing is not recommended. Otherwise, such work should only be carried out with appropriate protective equipment (fine dust mask) and/or wet sandpaper. It's possible that the models are hollow. In this case, the model has drainage holes through which the liquid resin could leak out. The inside of the model was then also cured. Drainage holes can be closed with modelling putty. Resin is heat-sensitive and can therefore deform during the printing process, the removal of the support structures, post-process curing, or shipping. Hot water or a heat gun/hair dryer can quickly remedy this. The affected part is heated and then carefully bent into the correct position. Important noticeWarning! Not for children under the age of 3. Choking hazard due to small parts.This product is not a toy.
€26.00*
Orc Commander on Buffalo
28 mm scale for collectors, painters and gamer, Fantasy mass battle system compatible models, like e.g. Warhammer Fantasy, The Old World, Age of Sigmar, Kings of War, Oathmark, Dragon Rampant, or other fantasy miniature wargames.Orcs have an eye height of approx. 32 mm. Includes a sword as backup weapon that can be glued to the back or side. Please note that the models are supplied WITHOUT bases. The pictures show a digital render. The 3D files are from Peculiar Companions. These 3D files are produced and sold under a commercial licence. Most of the miniatures are printed after you order them. The long processing time allows me to sensibly plan my working and printing time. Whenever possible, I try to cut the processing time short. The models are delivered unpainted and unassambled. This is a 3D printed product made of UV hardened resin. Models are cleaned and completely cured with UV light. Before printing, a support structure needs to be added to the models, these are normally removed after printing, but leave "scars" on the model. These are production-related and do not represent a defect in the product. Remains of the support structure might still be on the model and can be removed with a sharp hobby knife. Resin dust is a health hazard if inhaled into the lungs. Sanding and filing is not recommended. Otherwise, such work should only be carried out with appropriate protective equipment (fine dust mask) and/or wet sandpaper. It's possible that the models are hollow. In this case, the model has drainage holes through which the liquid resin could leak out. The inside of the model was then also cured. Drainage holes can be closed with modelling putty. Resin is heat-sensitive and can therefore deform during the printing process, the removal of the support structures, post-process curing, or shipping. Hot water or a heat gun/hair dryer can quickly remedy this. The affected part is heated and then carefully bent into the correct position. Important noticeWarning! Not for children under the age of 3. Choking hazard due to small parts.This product is not a toy.
€9.00*
Orc Commander on foot
28 mm scale for collectors, painters and gamer, Fantasy mass battle system compatible models, like e.g. Warhammer Fantasy, The Old World, Age of Sigmar, Kings of War, Oathmark, Dragon Rampant, or other fantasy miniature wargames.Orcs have an eye height of approx. 32 mm.Please note that the models are supplied WITHOUT bases. The pictures show a digital render. The 3D files are from Peculiar Companions. These 3D files are produced and sold under a commercial licence. Most of the miniatures are printed after you order them. The long processing time allows me to sensibly plan my working and printing time. Whenever possible, I try to cut the processing time short. The models are delivered unpainted and unassambled. This is a 3D printed product made of UV hardened resin. Models are cleaned and completely cured with UV light. Before printing, a support structure needs to be added to the models, these are normally removed after printing, but leave "scars" on the model. These are production-related and do not represent a defect in the product. Remains of the support structure might still be on the model and can be removed with a sharp hobby knife. Resin dust is a health hazard if inhaled into the lungs. Sanding and filing is not recommended. Otherwise, such work should only be carried out with appropriate protective equipment (fine dust mask) and/or wet sandpaper. It's possible that the models are hollow. In this case, the model has drainage holes through which the liquid resin could leak out. The inside of the model was then also cured. Drainage holes can be closed with modelling putty. Resin is heat-sensitive and can therefore deform during the printing process, the removal of the support structures, post-process curing, or shipping. Hot water or a heat gun/hair dryer can quickly remedy this. The affected part is heated and then carefully bent into the correct position. Important noticeWarning! Not for children under the age of 3. Choking hazard due to small parts.This product is not a toy.
€6.00*
Orc Infantry (10 models)
28 mm scale for collectors, painters and gamer, Fantasy mass battle system compatible models, like e.g. Warhammer Fantasy, The Old World, Age of Sigmar, Kings of War, Oathmark, Dragon Rampant, or other fantasy miniature wargames.Orcs have an eye height of approx. 32 mm.Contains 10x Orcs (six different variants, 4 random duplicates) and weapons of choice.Please note that the models are supplied WITHOUT bases. The pictures show a digital render. The 3D files are from Peculiar Companions. These 3D files are produced and sold under a commercial licence. Most of the miniatures are printed after you order them. The long processing time allows me to sensibly plan my working and printing time. Whenever possible, I try to cut the processing time short. The models are delivered unpainted and unassambled. This is a 3D printed product made of UV hardened resin. Models are cleaned and completely cured with UV light. Before printing, a support structure needs to be added to the models, these are normally removed after printing, but leave "scars" on the model. These are production-related and do not represent a defect in the product. Remains of the support structure might still be on the model and can be removed with a sharp hobby knife. Resin dust is a health hazard if inhaled into the lungs. Sanding and filing is not recommended. Otherwise, such work should only be carried out with appropriate protective equipment (fine dust mask) and/or wet sandpaper. It's possible that the models are hollow. In this case, the model has drainage holes through which the liquid resin could leak out. The inside of the model was then also cured. Drainage holes can be closed with modelling putty. Resin is heat-sensitive and can therefore deform during the printing process, the removal of the support structures, post-process curing, or shipping. Hot water or a heat gun/hair dryer can quickly remedy this. The affected part is heated and then carefully bent into the correct position. Important noticeWarning! Not for children under the age of 3. Choking hazard due to small parts.This product is not a toy.
€23.00*