Sarin Class Weapons Battery Destroyers (3 models)

Spaceships of the Akkadian Fleet for collectors, painters and gamers, eg. for Battlefleet Gothic, Firestorm Armada, Full Thrust, A Billion Suns, Warfleets: FTL, Dropfleet Commander or other Science Fiction spaceship miniature wargame.Please note that the models are supplied WITHOUT bases. The pictures show a digital render. The 3D files are from Italianmoose. These 3D files are produced and sold under a commercial licence. Printed and painted model by Italianmoose.Most of the miniatures are printed after you order them. The long processing time allows me to sensibly plan my working and printing time. Whenever possible, I try to cut the processing time short. The models are delivered unpainted and unassambled. This is a 3D printed product made of UV hardened resin. Models are cleaned and completely cured with UV light. Before printing, a support structure needs to be added to the models, these are normally removed after printing, but leave "scars" on the model. These are production-related and do not represent a defect in the product. Remains of the support structure might still be on the model and can be removed with a sharp hobby knife. Resin dust is a health hazard if inhaled into the lungs. Sanding and filing is not recommended. Otherwise, such work should only be carried out with appropriate protective equipment (fine dust mask) and/or wet sandpaper. It's possible that the models are hollow. In this case, the model has drainage holes through which the liquid resin could leak out. The inside of the model was then also cured. Drainage holes can be closed with modelling putty. Resin is heat-sensitive and can therefore deform during the printing process, the removal of the support structures, post-process curing, or shipping. Hot water or a heat gun/hair dryer can quickly remedy this. The affected part is heated and then carefully bent into the correct position. Important noticeWarning! Not for children under the age of 3. Choking hazard due to small parts.This product is not a toy.

Spaceships of the Akkadian Fleet for collectors, painters and gamers, eg. for Battlefleet Gothic, Firestorm Armada, Full Thrust, A Billion Suns, Warfleets: FTL, Dropfleet Commander or other Science Fiction spaceship miniature wargame.Please note that the models are supplied WITHOUT bases. The pictures show a digital render. The 3D files are from Italianmoose. These 3D files are produced and sold under a commercial licence. Printed and painted model by Italianmoose.Most of the miniatures are printed after you order them. The long processing time allows me to sensibly plan my working and printing time. Whenever possible, I try to cut the processing time short. The models are delivered unpainted and unassambled. This is a 3D printed product made of UV hardened resin. Models are cleaned and completely cured with UV light. Before printing, a support structure needs to be added to the models, these are normally removed after printing, but leave "scars" on the model. These are production-related and do not represent a defect in the product. Remains of the support structure might still be on the model and can be removed with a sharp hobby knife. Resin dust is a health hazard if inhaled into the lungs. Sanding and filing is not recommended. Otherwise, such work should only be carried out with appropriate protective equipment (fine dust mask) and/or wet sandpaper. It's possible that the models are hollow. In this case, the model has drainage holes through which the liquid resin could leak out. The inside of the model was then also cured. Drainage holes can be closed with modelling putty. Resin is heat-sensitive and can therefore deform during the printing process, the removal of the support structures, post-process curing, or shipping. Hot water or a heat gun/hair dryer can quickly remedy this. The affected part is heated and then carefully bent into the correct position. Important noticeWarning! Not for children under the age of 3. Choking hazard due to small parts.This product is not a toy.

Spaceships of the Akkadian Fleet for collectors, painters and gamers, eg. for Battlefleet Gothic, Firestorm Armada, Full Thrust, A Billion Suns, Warfleets: FTL, Dropfleet Commander or other Science Fiction spaceship miniature wargame.Please note that the models are supplied WITHOUT bases. The pictures show a digital render. The 3D files are from Italianmoose. These 3D files are produced and sold under a commercial licence. Printed and painted model by Italianmoose.Most of the miniatures are printed after you order them. The long processing time allows me to sensibly plan my working and printing time. Whenever possible, I try to cut the processing time short. The models are delivered unpainted and unassambled. This is a 3D printed product made of UV hardened resin. Models are cleaned and completely cured with UV light. Before printing, a support structure needs to be added to the models, these are normally removed after printing, but leave "scars" on the model. These are production-related and do not represent a defect in the product. Remains of the support structure might still be on the model and can be removed with a sharp hobby knife. Resin dust is a health hazard if inhaled into the lungs. Sanding and filing is not recommended. Otherwise, such work should only be carried out with appropriate protective equipment (fine dust mask) and/or wet sandpaper. It's possible that the models are hollow. In this case, the model has drainage holes through which the liquid resin could leak out. The inside of the model was then also cured. Drainage holes can be closed with modelling putty. Resin is heat-sensitive and can therefore deform during the printing process, the removal of the support structures, post-process curing, or shipping. Hot water or a heat gun/hair dryer can quickly remedy this. The affected part is heated and then carefully bent into the correct position. Important noticeWarning! Not for children under the age of 3. Choking hazard due to small parts.This product is not a toy.

Spaceships of the Akkadian Fleet for collectors, painters and gamers, eg. for Battlefleet Gothic, Firestorm Armada, Full Thrust, A Billion Suns, Warfleets: FTL, Dropfleet Commander or other Science Fiction spaceship miniature wargame.Please note that the models are supplied WITHOUT bases. The pictures show a digital render. The 3D files are from Italianmoose. These 3D files are produced and sold under a commercial licence. Printed and painted model by Italianmoose.Most of the miniatures are printed after you order them. The long processing time allows me to sensibly plan my working and printing time. Whenever possible, I try to cut the processing time short. The models are delivered unpainted and unassambled. This is a 3D printed product made of UV hardened resin. Models are cleaned and completely cured with UV light. Before printing, a support structure needs to be added to the models, these are normally removed after printing, but leave "scars" on the model. These are production-related and do not represent a defect in the product. Remains of the support structure might still be on the model and can be removed with a sharp hobby knife. Resin dust is a health hazard if inhaled into the lungs. Sanding and filing is not recommended. Otherwise, such work should only be carried out with appropriate protective equipment (fine dust mask) and/or wet sandpaper. It's possible that the models are hollow. In this case, the model has drainage holes through which the liquid resin could leak out. The inside of the model was then also cured. Drainage holes can be closed with modelling putty. Resin is heat-sensitive and can therefore deform during the printing process, the removal of the support structures, post-process curing, or shipping. Hot water or a heat gun/hair dryer can quickly remedy this. The affected part is heated and then carefully bent into the correct position. Important noticeWarning! Not for children under the age of 3. Choking hazard due to small parts.This product is not a toy.

Spaceships of the Renegade Super Warriors or Chaos for collectors, painters and gamers, eg. for Battlefleet Gothic, Firestorm Armada, Full Thrust, A Billion Suns, Warfleets: FTL, Dropfleet Commander or other Science Fiction spaceship miniature wargame. Armed with a prow lance and lateral weapons batteries. Non-modular. Please note that the models are supplied WITHOUT bases. The pictures show a digital render. The 3D files are from Italianmoose. These 3D files are produced and sold under a commercial licence. Most of the miniatures are printed after you order them. The long processing time allows me to sensibly plan my working and printing time. Whenever possible, I try to cut the processing time short. The models are delivered unpainted and unassambled. This is a 3D printed product made of UV hardened resin. Models are cleaned and completely cured with UV light. Before printing, a support structure needs to be added to the models, these are normally removed after printing, but leave "scars" on the model. These are production-related and do not represent a defect in the product. Remains of the support structure might still be on the model and can be removed with a sharp hobby knife. Resin dust is a health hazard if inhaled into the lungs. Sanding and filing is not recommended. Otherwise, such work should only be carried out with appropriate protective equipment (fine dust mask) and/or wet sandpaper. It's possible that the models are hollow. In this case, the model has drainage holes through which the liquid resin could leak out. The inside of the model was then also cured. Drainage holes can be closed with modelling putty. Resin is heat-sensitive and can therefore deform during the printing process, the removal of the support structures, post-process curing, or shipping. Hot water or a heat gun/hair dryer can quickly remedy this. The affected part is heated and then carefully bent into the correct position. Important noticeWarning! Not for children under the age of 3. Choking hazard due to small parts.This product is not a toy.

Spaceships of the Renegade Super Warriors or Chaos for collectors, painters and gamers, eg. for Battlefleet Gothic, Firestorm Armada, Full Thrust, A Billion Suns, Warfleets: FTL, Dropfleet Commander or other Science Fiction spaceship miniature wargame.Choose the options to fit the battleship to your needs. Every ship comes with a sprue of 6 turrets (2 per type - Lance, Heavy lance, Heavy turret) Two popular Chaos choices: Variant 1: Prow: Edge, Bridge: Battle, 2x Heavy turrets, 3x pairs Lance batteries (any type)Variant 2: Prow: Pincer, Bridge: Carrier, 2x Lance turrets (any type), 2x pairs long-range weapons batteries, 1x pair launch bays Please note that the models are supplied WITHOUT bases. The pictures show a digital render. The 3D files are from Italianmoose. These 3D files are produced and sold under a commercial licence. Most of the miniatures are printed after you order them. The long processing time allows me to sensibly plan my working and printing time. Whenever possible, I try to cut the processing time short. The models are delivered unpainted and unassambled. This is a 3D printed product made of UV hardened resin. Models are cleaned and completely cured with UV light. Before printing, a support structure needs to be added to the models, these are normally removed after printing, but leave "scars" on the model. These are production-related and do not represent a defect in the product. Remains of the support structure might still be on the model and can be removed with a sharp hobby knife. Resin dust is a health hazard if inhaled into the lungs. Sanding and filing is not recommended. Otherwise, such work should only be carried out with appropriate protective equipment (fine dust mask) and/or wet sandpaper. It's possible that the models are hollow. In this case, the model has drainage holes through which the liquid resin could leak out. The inside of the model was then also cured. Drainage holes can be closed with modelling putty. Resin is heat-sensitive and can therefore deform during the printing process, the removal of the support structures, post-process curing, or shipping. Hot water or a heat gun/hair dryer can quickly remedy this. The affected part is heated and then carefully bent into the correct position. Important noticeWarning! Not for children under the age of 3. Choking hazard due to small parts.This product is not a toy.

Spaceships of the Renegade Super Warriors or Chaos for collectors, painters and gamers, eg. for Battlefleet Gothic, Firestorm Armada, Full Thrust, A Billion Suns, Warfleets: FTL, Dropfleet Commander or other Science Fiction spaceship miniature wargame.Please note that the models are supplied WITHOUT bases. The pictures show a digital render. The 3D files are from Italianmoose. These 3D files are produced and sold under a commercial licence. Most of the miniatures are printed after you order them. The long processing time allows me to sensibly plan my working and printing time. Whenever possible, I try to cut the processing time short. The models are delivered unpainted and unassambled. This is a 3D printed product made of UV hardened resin. Models are cleaned and completely cured with UV light. Before printing, a support structure needs to be added to the models, these are normally removed after printing, but leave "scars" on the model. These are production-related and do not represent a defect in the product. Remains of the support structure might still be on the model and can be removed with a sharp hobby knife. Resin dust is a health hazard if inhaled into the lungs. Sanding and filing is not recommended. Otherwise, such work should only be carried out with appropriate protective equipment (fine dust mask) and/or wet sandpaper. It's possible that the models are hollow. In this case, the model has drainage holes through which the liquid resin could leak out. The inside of the model was then also cured. Drainage holes can be closed with modelling putty. Resin is heat-sensitive and can therefore deform during the printing process, the removal of the support structures, post-process curing, or shipping. Hot water or a heat gun/hair dryer can quickly remedy this. The affected part is heated and then carefully bent into the correct position. Important noticeWarning! Not for children under the age of 3. Choking hazard due to small parts.This product is not a toy.

Spaceships of the Renegade Super Warriors or Chaos for collectors, painters and gamers, eg. for Battlefleet Gothic, Firestorm Armada, Full Thrust, A Billion Suns, Warfleets: FTL, Dropfleet Commander or other Science Fiction spaceship miniature wargame.Please note that the models are supplied WITHOUT bases. The pictures show a digital render. The 3D files are from Italianmoose. These 3D files are produced and sold under a commercial licence. Most of the miniatures are printed after you order them. The long processing time allows me to sensibly plan my working and printing time. Whenever possible, I try to cut the processing time short. The models are delivered unpainted and unassambled. This is a 3D printed product made of UV hardened resin. Models are cleaned and completely cured with UV light. Before printing, a support structure needs to be added to the models, these are normally removed after printing, but leave "scars" on the model. These are production-related and do not represent a defect in the product. Remains of the support structure might still be on the model and can be removed with a sharp hobby knife. Resin dust is a health hazard if inhaled into the lungs. Sanding and filing is not recommended. Otherwise, such work should only be carried out with appropriate protective equipment (fine dust mask) and/or wet sandpaper. It's possible that the models are hollow. In this case, the model has drainage holes through which the liquid resin could leak out. The inside of the model was then also cured. Drainage holes can be closed with modelling putty. Resin is heat-sensitive and can therefore deform during the printing process, the removal of the support structures, post-process curing, or shipping. Hot water or a heat gun/hair dryer can quickly remedy this. The affected part is heated and then carefully bent into the correct position. Important noticeWarning! Not for children under the age of 3. Choking hazard due to small parts.This product is not a toy.

Spaceships weaponry for the Chaos ships (including Alces pattern and Dark Engineers) from Italianmoose. Each selection is included twice. With the two selected options, a cruiser is completely armed and each loadout configuration possible. The pictures show a digital render. The 3D files are from Italianmoose. These 3D files are produced and sold under a commercial licence. Most of the miniatures are printed after you order them. The long processing time allows me to sensibly plan my working and printing time. Whenever possible, I try to cut the processing time short. The models are delivered unpainted and unassambled. This is a 3D printed product made of UV hardened resin. Models are cleaned and completely cured with UV light. Before printing, a support structure needs to be added to the models, these are normally removed after printing, but leave "scars" on the model. These are production-related and do not represent a defect in the product. Remains of the support structure might still be on the model and can be removed with a sharp hobby knife. Resin dust is a health hazard if inhaled into the lungs. Sanding and filing is not recommended. Otherwise, such work should only be carried out with appropriate protective equipment (fine dust mask) and/or wet sandpaper. It's possible that the models are hollow. In this case, the model has drainage holes through which the liquid resin could leak out. The inside of the model was then also cured. Drainage holes can be closed with modelling putty. Resin is heat-sensitive and can therefore deform during the printing process, the removal of the support structures, post-process curing, or shipping. Hot water or a heat gun/hair dryer can quickly remedy this. The affected part is heated and then carefully bent into the correct position. Important noticeWarning! Not for children under the age of 3. Choking hazard due to small parts.This product is not a toy.

Chaos spaceship of the Cathedral Fleet. For collectors, painters and gamers, eg. for Battlefleet Gothic, Firestorm Armada, Full Thrust, A Billion Suns, Warfleets: FTL, Dropfleet Commander or other Science Fiction spaceship miniature wargames. Includes one set of antennas in addition to any chosen options. Please note that the models are supplied WITHOUT bases. The pictures show a digital render. The 3D files are from NofixedForge These 3D files are produced and sold under a commercial licence. Printed and painted model by NofixedForge. Most of the miniatures are printed after you order them. The long processing time allows me to sensibly plan my working and printing time. Whenever possible, I try to cut the processing time short. The models are delivered unpainted and unassambled. This is a 3D printed product made of UV hardened resin. Models are cleaned and completely cured with UV light. Before printing, a support structure needs to be added to the models, these are normally removed after printing, but leave "scars" on the model. These are production-related and do not represent a defect in the product. Remains of the support structure might still be on the model and can be removed with a sharp hobby knife. Resin dust is a health hazard if inhaled into the lungs. Sanding and filing is not recommended. Otherwise, such work should only be carried out with appropriate protective equipment (fine dust mask) and/or wet sandpaper. It's possible that the models are hollow. In this case, the model has drainage holes through which the liquid resin could leak out. The inside of the model was then also cured. Drainage holes can be closed with modelling putty. Resin is heat-sensitive and can therefore deform during the printing process, the removal of the support structures, post-process curing, or shipping. Hot water or a heat gun/hair dryer can quickly remedy this. The affected part is heated and then carefully bent into the correct position. Important noticeWarning! Not for children under the age of 3. Choking hazard due to small parts.This product is not a toy.

Attack wave markers for collectors, painters and gamers, eg. for Battlefleet Gothic, Firestorm Armada, Full Thrust, A Billion Suns, Warfleets: FTL, Dropfleet Commander or other Science Fiction spaceship miniature wargames. 5x fighter markers (5 ships), 5x bomber markers (3 ships), 5x assault boat markers (2 ships). Stackable. Please note that the models are supplied WITHOUT bases. The pictures show a digital render. The 3D files are from Keiler. These 3D files are produced and sold under a commercial licence. Most of the miniatures are printed after you order them. The long processing time allows me to sensibly plan my working and printing time. Whenever possible, I try to cut the processing time short. The models are delivered unpainted and unassambled. This is a 3D printed product made of UV hardened resin. Models are cleaned and completely cured with UV light. Before printing, a support structure needs to be added to the models, these are normally removed after printing, but leave "scars" on the model. These are production-related and do not represent a defect in the product. Remains of the support structure might still be on the model and can be removed with a sharp hobby knife. Resin dust is a health hazard if inhaled into the lungs. Sanding and filing is not recommended. Otherwise, such work should only be carried out with appropriate protective equipment (fine dust mask) and/or wet sandpaper. It's possible that the models are hollow. In this case, the model has drainage holes through which the liquid resin could leak out. The inside of the model was then also cured. Drainage holes can be closed with modelling putty. Resin is heat-sensitive and can therefore deform during the printing process, the removal of the support structures, post-process curing, or shipping. Hot water or a heat gun/hair dryer can quickly remedy this. The affected part is heated and then carefully bent into the correct position. Important noticeWarning! Not for children under the age of 3. Choking hazard due to small parts.This product is not a toy.

For space miniature war- and boardgames like e.g. for Battlefleet Gothic, Dropfleet Commander, Firestorm Armada, Full Thrust, A Billion Suns, Warfleets: FTL, Void Admiral, Brutal Space, or Twilight Imperium. Please note that the models are supplied WITHOUT bases. The pictures show a printed and painted product, often in conjunction with additional digital render images. The 3D files are from NofixedForge These 3D files are produced and sold under a commercial licence. Printed and painted model by NofixedForge. Most of the miniatures are printed after you order them. The long processing time allows me to sensibly plan my working and printing time. Whenever possible, I try to cut the processing time short. The models are delivered unpainted and unassambled. This is a 3D printed product made of UV hardened resin. Models are cleaned and completely cured with UV light. Before printing, a support structure needs to be added to the models, these are normally removed after printing, but leave "scars" on the model. These are production-related and do not represent a defect in the product. Remains of the support structure might still be on the model and can be removed with a sharp hobby knife. Resin dust is a health hazard if inhaled into the lungs. Sanding and filing is not recommended. Otherwise, such work should only be carried out with appropriate protective equipment (fine dust mask) and/or wet sandpaper. It's possible that the models are hollow. In this case, the model has drainage holes through which the liquid resin could leak out. The inside of the model was then also cured. Drainage holes can be closed with modelling putty. Resin is heat-sensitive and can therefore deform during the printing process, the removal of the support structures, post-process curing, or shipping. Hot water or a heat gun/hair dryer can quickly remedy this. The affected part is heated and then carefully bent into the correct position. Important noticeWarning! Not for children under the age of 3. Choking hazard due to small parts.This product is not a toy.

Chaos spaceships of the Cathedral Fleet. For collectors, painters and gamers, eg. for Battlefleet Gothic, Firestorm Armada, Full Thrust, A Billion Suns, Warfleets: FTL, Dropfleet Commander or other Science Fiction spaceship miniature wargames. Each of the three ships has a different cargo (bulk, fuel, and troops). Please note that the models are supplied WITHOUT bases. The pictures show a printed and painted product, often in conjunction with additional digital render images. The 3D files are from NofixedForge These 3D files are produced and sold under a commercial licence. Printed and painted model by NofixedForge. Most of the miniatures are printed after you order them. The long processing time allows me to sensibly plan my working and printing time. Whenever possible, I try to cut the processing time short. The models are delivered unpainted and unassambled. This is a 3D printed product made of UV hardened resin. Models are cleaned and completely cured with UV light. Before printing, a support structure needs to be added to the models, these are normally removed after printing, but leave "scars" on the model. These are production-related and do not represent a defect in the product. Remains of the support structure might still be on the model and can be removed with a sharp hobby knife. Resin dust is a health hazard if inhaled into the lungs. Sanding and filing is not recommended. Otherwise, such work should only be carried out with appropriate protective equipment (fine dust mask) and/or wet sandpaper. It's possible that the models are hollow. In this case, the model has drainage holes through which the liquid resin could leak out. The inside of the model was then also cured. Drainage holes can be closed with modelling putty. Resin is heat-sensitive and can therefore deform during the printing process, the removal of the support structures, post-process curing, or shipping. Hot water or a heat gun/hair dryer can quickly remedy this. The affected part is heated and then carefully bent into the correct position. Important noticeWarning! Not for children under the age of 3. Choking hazard due to small parts.This product is not a toy.

Raumschiffbewaffnung für die Chaos Schiffe von Keiler.Jede Auswahloption ist zweimal enthalten. Mit den zwei Auswahlen ist damit ein Kreuzer vollständig bewaffnet und jede mögliche Kombination abbildbar. Die Auswahl der Geschütztürme kommt nur zur Geltung, wenn mind. eine gemischte oder Lanzenbatterie ausgewählt wurde.The pictures show a digital render. The 3D files are from Keiler. These 3D files are produced and sold under a commercial licence. Most of the miniatures are printed after you order them. The long processing time allows me to sensibly plan my working and printing time. Whenever possible, I try to cut the processing time short. The models are delivered unpainted and unassambled. This is a 3D printed product made of UV hardened resin. Models are cleaned and completely cured with UV light. Before printing, a support structure needs to be added to the models, these are normally removed after printing, but leave "scars" on the model. These are production-related and do not represent a defect in the product. Remains of the support structure might still be on the model and can be removed with a sharp hobby knife. Resin dust is a health hazard if inhaled into the lungs. Sanding and filing is not recommended. Otherwise, such work should only be carried out with appropriate protective equipment (fine dust mask) and/or wet sandpaper. It's possible that the models are hollow. In this case, the model has drainage holes through which the liquid resin could leak out. The inside of the model was then also cured. Drainage holes can be closed with modelling putty. Resin is heat-sensitive and can therefore deform during the printing process, the removal of the support structures, post-process curing, or shipping. Hot water or a heat gun/hair dryer can quickly remedy this. The affected part is heated and then carefully bent into the correct position. Important noticeWarning! Not for children under the age of 3. Choking hazard due to small parts.This product is not a toy.

Chaos spaceships for collectors, painters and gamers, eg. for Battlefleet Gothic, Firestorm Armada, Full Thrust, A Billion Suns, Warfleets: FTL, Dropfleet Commander or other Science Fiction spaceship miniature wargame. Please note that the models are supplied WITHOUT bases. The pictures show a digital render. The 3D files are from Mkhand Industries. If you got a 3D printer yourself, you can print this object yourself. If needed by the licence, the creators of these files are informed about this listing and have given their permission to sell these prints. Most of the miniatures are printed after you order them. The long processing time allows me to sensibly plan my working and printing time. Whenever possible, I try to cut the processing time short. The models are delivered unpainted and unassambled. This is a 3D printed product made of UV hardened resin. Models are cleaned and completely cured with UV light. Before printing, a support structure needs to be added to the models, these are normally removed after printing, but leave "scars" on the model. These are production-related and do not represent a defect in the product. Remains of the support structure might still be on the model and can be removed with a sharp hobby knife. Resin dust is a health hazard if inhaled into the lungs. Sanding and filing is not recommended. Otherwise, such work should only be carried out with appropriate protective equipment (fine dust mask) and/or wet sandpaper. It's possible that the models are hollow. In this case, the model has drainage holes through which the liquid resin could leak out. The inside of the model was then also cured. Drainage holes can be closed with modelling putty. Resin is heat-sensitive and can therefore deform during the printing process, the removal of the support structures, post-process curing, or shipping. Hot water or a heat gun/hair dryer can quickly remedy this. The affected part is heated and then carefully bent into the correct position. Important noticeWarning! Not for children under the age of 3. Choking hazard due to small parts.This product is not a toy.

Chaos spaceship for collectors, painters and gamers, eg. for Battlefleet Gothic, Firestorm Armada, Full Thrust, A Billion Suns, Warfleets: FTL, Dropfleet Commander or other Science Fiction spaceship miniature wargame.Please note that the models are supplied WITHOUT bases. The pictures show a digital render. The 3D files are from Italianmoose. These 3D files are produced and sold under a commercial licence. Most of the miniatures are printed after you order them. The long processing time allows me to sensibly plan my working and printing time. Whenever possible, I try to cut the processing time short. The models are delivered unpainted and unassambled. This is a 3D printed product made of UV hardened resin. Models are cleaned and completely cured with UV light. Before printing, a support structure needs to be added to the models, these are normally removed after printing, but leave "scars" on the model. These are production-related and do not represent a defect in the product. Remains of the support structure might still be on the model and can be removed with a sharp hobby knife. Resin dust is a health hazard if inhaled into the lungs. Sanding and filing is not recommended. Otherwise, such work should only be carried out with appropriate protective equipment (fine dust mask) and/or wet sandpaper. It's possible that the models are hollow. In this case, the model has drainage holes through which the liquid resin could leak out. The inside of the model was then also cured. Drainage holes can be closed with modelling putty. Resin is heat-sensitive and can therefore deform during the printing process, the removal of the support structures, post-process curing, or shipping. Hot water or a heat gun/hair dryer can quickly remedy this. The affected part is heated and then carefully bent into the correct position. Important noticeWarning! Not for children under the age of 3. Choking hazard due to small parts.This product is not a toy.

Chaos spaceships for collectors, painters and gamers, eg. for Battlefleet Gothic, Firestorm Armada, Full Thrust, A Billion Suns, Warfleets: FTL, Dropfleet Commander or other Science Fiction spaceship miniature wargame.Please note that the models are supplied WITHOUT bases. The pictures show a digital render. The 3D files are from Italianmoose. These 3D files are produced and sold under a commercial licence. Most of the miniatures are printed after you order them. The long processing time allows me to sensibly plan my working and printing time. Whenever possible, I try to cut the processing time short. The models are delivered unpainted and unassambled. This is a 3D printed product made of UV hardened resin. Models are cleaned and completely cured with UV light. Before printing, a support structure needs to be added to the models, these are normally removed after printing, but leave "scars" on the model. These are production-related and do not represent a defect in the product. Remains of the support structure might still be on the model and can be removed with a sharp hobby knife. Resin dust is a health hazard if inhaled into the lungs. Sanding and filing is not recommended. Otherwise, such work should only be carried out with appropriate protective equipment (fine dust mask) and/or wet sandpaper. It's possible that the models are hollow. In this case, the model has drainage holes through which the liquid resin could leak out. The inside of the model was then also cured. Drainage holes can be closed with modelling putty. Resin is heat-sensitive and can therefore deform during the printing process, the removal of the support structures, post-process curing, or shipping. Hot water or a heat gun/hair dryer can quickly remedy this. The affected part is heated and then carefully bent into the correct position. Important noticeWarning! Not for children under the age of 3. Choking hazard due to small parts.This product is not a toy.

Chaos spaceship for collectors, painters and gamers, eg. for Battlefleet Gothic, Firestorm Armada, Full Thrust, A Billion Suns, Warfleets: FTL, Dropfleet Commander or other Science Fiction spaceship miniature wargames.Choose the options to display the desired weapons loadout/ship class.Please note that the models are supplied WITHOUT bases. The pictures show a digital render. The 3D files are from Keiler. These 3D files are produced and sold under a commercial licence. Most of the miniatures are printed after you order them. The long processing time allows me to sensibly plan my working and printing time. Whenever possible, I try to cut the processing time short. The models are delivered unpainted and unassambled. This is a 3D printed product made of UV hardened resin. Models are cleaned and completely cured with UV light. Before printing, a support structure needs to be added to the models, these are normally removed after printing, but leave "scars" on the model. These are production-related and do not represent a defect in the product. Remains of the support structure might still be on the model and can be removed with a sharp hobby knife. Resin dust is a health hazard if inhaled into the lungs. Sanding and filing is not recommended. Otherwise, such work should only be carried out with appropriate protective equipment (fine dust mask) and/or wet sandpaper. It's possible that the models are hollow. In this case, the model has drainage holes through which the liquid resin could leak out. The inside of the model was then also cured. Drainage holes can be closed with modelling putty. Resin is heat-sensitive and can therefore deform during the printing process, the removal of the support structures, post-process curing, or shipping. Hot water or a heat gun/hair dryer can quickly remedy this. The affected part is heated and then carefully bent into the correct position. Important noticeWarning! Not for children under the age of 3. Choking hazard due to small parts.This product is not a toy.

Chaos spaceship for collectors, painters and gamers, eg. for Battlefleet Gothic, Firestorm Armada, Full Thrust, A Billion Suns, Warfleets: FTL, Dropfleet Commander or other Science Fiction spaceship miniature wargames.Choose the options to display the desired weapons loadout/ship class.Please note that the models are supplied WITHOUT bases. The pictures show a digital render. The 3D files are from Keiler. These 3D files are produced and sold under a commercial licence. Most of the miniatures are printed after you order them. The long processing time allows me to sensibly plan my working and printing time. Whenever possible, I try to cut the processing time short. The models are delivered unpainted and unassambled. This is a 3D printed product made of UV hardened resin. Models are cleaned and completely cured with UV light. Before printing, a support structure needs to be added to the models, these are normally removed after printing, but leave "scars" on the model. These are production-related and do not represent a defect in the product. Remains of the support structure might still be on the model and can be removed with a sharp hobby knife. Resin dust is a health hazard if inhaled into the lungs. Sanding and filing is not recommended. Otherwise, such work should only be carried out with appropriate protective equipment (fine dust mask) and/or wet sandpaper. It's possible that the models are hollow. In this case, the model has drainage holes through which the liquid resin could leak out. The inside of the model was then also cured. Drainage holes can be closed with modelling putty. Resin is heat-sensitive and can therefore deform during the printing process, the removal of the support structures, post-process curing, or shipping. Hot water or a heat gun/hair dryer can quickly remedy this. The affected part is heated and then carefully bent into the correct position. Important noticeWarning! Not for children under the age of 3. Choking hazard due to small parts.This product is not a toy.

Chaos spaceship for collectors, painters and gamers, eg. for Battlefleet Gothic, Firestorm Armada, Full Thrust, A Billion Suns, Warfleets: FTL, Dropfleet Commander or other Science Fiction spaceship miniature wargames.Please note that the models are supplied WITHOUT bases. The pictures show a digital render. The 3D files are from Keiler. These 3D files are produced and sold under a commercial licence. Most of the miniatures are printed after you order them. The long processing time allows me to sensibly plan my working and printing time. Whenever possible, I try to cut the processing time short. The models are delivered unpainted and unassambled. This is a 3D printed product made of UV hardened resin. Models are cleaned and completely cured with UV light. Before printing, a support structure needs to be added to the models, these are normally removed after printing, but leave "scars" on the model. These are production-related and do not represent a defect in the product. Remains of the support structure might still be on the model and can be removed with a sharp hobby knife. Resin dust is a health hazard if inhaled into the lungs. Sanding and filing is not recommended. Otherwise, such work should only be carried out with appropriate protective equipment (fine dust mask) and/or wet sandpaper. It's possible that the models are hollow. In this case, the model has drainage holes through which the liquid resin could leak out. The inside of the model was then also cured. Drainage holes can be closed with modelling putty. Resin is heat-sensitive and can therefore deform during the printing process, the removal of the support structures, post-process curing, or shipping. Hot water or a heat gun/hair dryer can quickly remedy this. The affected part is heated and then carefully bent into the correct position. Important noticeWarning! Not for children under the age of 3. Choking hazard due to small parts.This product is not a toy.

Chaos spaceship for collectors, painters and gamers, eg. for Battlefleet Gothic, Firestorm Armada, Full Thrust, A Billion Suns, Warfleets: FTL, Dropfleet Commander or other Science Fiction spaceship miniature wargames.Choose the options to display the desired weapons loadout/ship class.Please note that the models are supplied WITHOUT bases. The pictures show a digital render. The 3D files are from Keiler. These 3D files are produced and sold under a commercial licence. Most of the miniatures are printed after you order them. The long processing time allows me to sensibly plan my working and printing time. Whenever possible, I try to cut the processing time short. The models are delivered unpainted and unassambled. This is a 3D printed product made of UV hardened resin. Models are cleaned and completely cured with UV light. Before printing, a support structure needs to be added to the models, these are normally removed after printing, but leave "scars" on the model. These are production-related and do not represent a defect in the product. Remains of the support structure might still be on the model and can be removed with a sharp hobby knife. Resin dust is a health hazard if inhaled into the lungs. Sanding and filing is not recommended. Otherwise, such work should only be carried out with appropriate protective equipment (fine dust mask) and/or wet sandpaper. It's possible that the models are hollow. In this case, the model has drainage holes through which the liquid resin could leak out. The inside of the model was then also cured. Drainage holes can be closed with modelling putty. Resin is heat-sensitive and can therefore deform during the printing process, the removal of the support structures, post-process curing, or shipping. Hot water or a heat gun/hair dryer can quickly remedy this. The affected part is heated and then carefully bent into the correct position. Important noticeWarning! Not for children under the age of 3. Choking hazard due to small parts.This product is not a toy.

Chaos spaceship for collectors, painters and gamers, eg. for Battlefleet Gothic, Firestorm Armada, Full Thrust, A Billion Suns, Warfleets: FTL, Dropfleet Commander or other Science Fiction spaceship miniature wargames.Choose the options to display the desired weapons loadout/ship class. Please note that the models are supplied WITHOUT bases. The pictures show a digital render. The 3D files are from Keiler. These 3D files are produced and sold under a commercial licence. Most of the miniatures are printed after you order them. The long processing time allows me to sensibly plan my working and printing time. Whenever possible, I try to cut the processing time short. The models are delivered unpainted and unassambled. This is a 3D printed product made of UV hardened resin. Models are cleaned and completely cured with UV light. Before printing, a support structure needs to be added to the models, these are normally removed after printing, but leave "scars" on the model. These are production-related and do not represent a defect in the product. Remains of the support structure might still be on the model and can be removed with a sharp hobby knife. Resin dust is a health hazard if inhaled into the lungs. Sanding and filing is not recommended. Otherwise, such work should only be carried out with appropriate protective equipment (fine dust mask) and/or wet sandpaper. It's possible that the models are hollow. In this case, the model has drainage holes through which the liquid resin could leak out. The inside of the model was then also cured. Drainage holes can be closed with modelling putty. Resin is heat-sensitive and can therefore deform during the printing process, the removal of the support structures, post-process curing, or shipping. Hot water or a heat gun/hair dryer can quickly remedy this. The affected part is heated and then carefully bent into the correct position. Important noticeWarning! Not for children under the age of 3. Choking hazard due to small parts.This product is not a toy.

Chaos spaceships for collectors, painters and gamers, eg. for Battlefleet Gothic, Firestorm Armada, Full Thrust, A Billion Suns, Warfleets: FTL, Dropfleet Commander or other Science Fiction spaceship miniature wargames.Please note that the models are supplied WITHOUT bases. The pictures show a digital render. The 3D files are from Keiler. These 3D files are produced and sold under a commercial licence. Most of the miniatures are printed after you order them. The long processing time allows me to sensibly plan my working and printing time. Whenever possible, I try to cut the processing time short. The models are delivered unpainted and unassambled. This is a 3D printed product made of UV hardened resin. Models are cleaned and completely cured with UV light. Before printing, a support structure needs to be added to the models, these are normally removed after printing, but leave "scars" on the model. These are production-related and do not represent a defect in the product. Remains of the support structure might still be on the model and can be removed with a sharp hobby knife. Resin dust is a health hazard if inhaled into the lungs. Sanding and filing is not recommended. Otherwise, such work should only be carried out with appropriate protective equipment (fine dust mask) and/or wet sandpaper. It's possible that the models are hollow. In this case, the model has drainage holes through which the liquid resin could leak out. The inside of the model was then also cured. Drainage holes can be closed with modelling putty. Resin is heat-sensitive and can therefore deform during the printing process, the removal of the support structures, post-process curing, or shipping. Hot water or a heat gun/hair dryer can quickly remedy this. The affected part is heated and then carefully bent into the correct position. Important noticeWarning! Not for children under the age of 3. Choking hazard due to small parts.This product is not a toy.

Chaos spaceships for collectors, painters and gamers, eg. for Battlefleet Gothic, Firestorm Armada, Full Thrust, A Billion Suns, Warfleets: FTL, Dropfleet Commander or other Science Fiction spaceship miniature wargame.Please note that the models are supplied WITHOUT bases. The pictures show a digital render. The 3D files are from Italianmoose. These 3D files are produced and sold under a commercial licence. Most of the miniatures are printed after you order them. The long processing time allows me to sensibly plan my working and printing time. Whenever possible, I try to cut the processing time short. The models are delivered unpainted and unassambled. This is a 3D printed product made of UV hardened resin. Models are cleaned and completely cured with UV light. Before printing, a support structure needs to be added to the models, these are normally removed after printing, but leave "scars" on the model. These are production-related and do not represent a defect in the product. Remains of the support structure might still be on the model and can be removed with a sharp hobby knife. Resin dust is a health hazard if inhaled into the lungs. Sanding and filing is not recommended. Otherwise, such work should only be carried out with appropriate protective equipment (fine dust mask) and/or wet sandpaper. It's possible that the models are hollow. In this case, the model has drainage holes through which the liquid resin could leak out. The inside of the model was then also cured. Drainage holes can be closed with modelling putty. Resin is heat-sensitive and can therefore deform during the printing process, the removal of the support structures, post-process curing, or shipping. Hot water or a heat gun/hair dryer can quickly remedy this. The affected part is heated and then carefully bent into the correct position. Important noticeWarning! Not for children under the age of 3. Choking hazard due to small parts.This product is not a toy.